EasyManua.ls Logo

Parker PV180 - User Manual

Parker PV180
16 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Visit our homepage for additional support
parker.com/pmde
Effective: December 20, 2018
Supersedes: July 1, 2010
Bulletin MSG30-3245-INST/UK
Installation and
start-up information
PV series
Design series ≥ 44, PVplus
Variable displacement
axial piston pump

Table of Contents

Questions and Answers

  • Z
    Zachary JacksonAug 17, 2025
    What to do if my Parker PV180 Water Pump drive motor does not turn?
    • N
      Nicole ReillyAug 17, 2025
      If the drive motor of your Parker Water Pump isn't turning, it could be due to a few reasons. First, check the motor connections and the electrical power supply to ensure they are correctly connected and functioning. It's possible that one of the three phases has failed. If the motor connections and power supply are fine, the pump may be mechanically blocked, in which case you should send the pump to the factory for service.
  • M
    Melissa TaylorAug 21, 2025
    Why Parker PV180 Water Pump drive motor turns, but pump does not turn?
    • T
      tmyersAug 21, 2025
      If the drive motor of your Parker Water Pump is turning but the pump itself isn't, the coupling might not be mounted correctly. Check the coupling assembly and correct it.
  • I
    ihaneyAug 25, 2025
    What to do if Parker PV180 Water Pump drive motor turns and pump turns, but there is no output?
    • Q
      qhenryAug 25, 2025
      If the drive motor and pump of your Parker Water Pump are both turning, but there's no output, consider these possibilities: Ensure the direction of motor rotation is correct by changing it if necessary. Check that the fluid reservoir is filled to the required level and increase the suction pipe length if needed. Inspect the suction line for blockages and open any valves in the line, ensuring they have electrical indicators. Also, check the suction filter. Seal the suction line to prevent air from entering. Unload the pressure port and system before starting, and bleed air from the pressure line if the pressure line/system cannot bleed air out.
  • M
    Melissa WhiteAug 29, 2025
    How to fix unstable compensator on Parker PV180?
    • R
      Robert WestAug 29, 2025
      To address an unstable compensator in your Parker Water Pump, consider these steps: First, clean the hydraulic system and compensator valve, as the compensator spool might be sticking due to hydraulic fluid contamination. Next, adjust the compensator differential pressure to the required setting, as it may have changed (becoming too low or too high). Ensure the correct pilot orifice and pressure pilot valve are selected as recommended. If dealing with a dynamic critical system, such as a pressure compensator combined with a pressure reducing valve, use a remote pressure compensator instead of a standard one, and install an orifice in the load sensing line remote from the compensator, as close as possible to the load sensing valve.
  • T
    Tiffany MarshSep 1, 2025
    What to do if Parker PV180 Water Pump does not compensate?
    • C
      Christina SharpSep 1, 2025
      If your Parker Water Pump isn't compensating, check these potential issues: Ensure there is an orifice Ø 0.8 mm in the load sensing line to compensator code MFC. Verify that a pressure pilot valve is connected to the compensator and that the valve opens as required. Confirm that the load sensing line is connected downstream (actuator side) of the load sensing valve. Also, ensure that the pump outlet pressure is at least 15 bar, as the bias spring in the pump cannot be compressed otherwise.
  • L
    Lisa GriffithSep 5, 2025
    Why Parker PV180 Water Pump drive motor only turns at slow speed?
    • L
      Lisa EricksonSep 5, 2025
      If the drive motor of your Parker Water Pump only turns at slow speed, it could be due to improper motor selection or a hydraulically blocked pump. Start the pump at an unloaded system and consider using a motor with more horsepower. Also, check the function of the pump compensator and start the pump at an unloaded system.
  • M
    Michelle PaulSep 9, 2025
    What to do if Parker Water Pump does not upstroke?
    • M
      Martin FlynnSep 9, 2025
      If your Parker Water Pump does not upstroke and sticks at zero displacement, it could be due to a blocked compensator or an interrupted cable. Clean the hydraulic fluid and compensator valve, as the compensator might be blocked due to contamination. Check the wiring to the LVDT or proportional solenoid to ensure the cable is intact; replace it if necessary.
  • E
    Evan WilliamsNov 12, 2025
    What to do if Parker PV180 delivers full flow at low pressure?
    • T
      Tricia SchneiderNov 12, 2025
      If your Parker Water Pump delivers full flow at low pressure, several issues could be the cause. The standard pressure compensator might be set to minimum pressure, so you should adjust the compensator setting to the desired pressure. Alternatively, the orifice in the remote pressure compensator could be blocked, so ensure the orifice Ø 0.8 mm in the control spool is free and open. Other potential causes include: a missing pressure pilot valve connected to port P. R (install a suitable pressure pilot valve and adjust it); an unenergized multiple pressure pilot selector valve (energize the selector valve solenoid); a missing load sensing line (connect the system load sensing port to the compensator); a closed or too small load sensing valve (open the load sensing valve or use a larger valve...

Summary

Installation and Start-up Procedures

Visual Inspection

Cleanliness Requirements

Emphasizes that contamination is the primary cause of hydraulic component failure.

Installation Guidelines

Suction Port Configuration

Details on fluid velocity, pipe length, and ensuring gas-tight connections.

Pressure Port Requirements

Drain Port Setup

Instructions for using the highest possible drain port and ensuring proper case pressure.

Flushing, Drive, and Fluid Systems

Filtration Importance

Highlights filtration as crucial for operational life and details cleanliness levels.

Pump Case Filling

Displacement Adjustment

Adjusting the Displacement Limiter

Details on adjusting the pump's displacement limiter screw and lock nut.

Standard Pressure Compensator (MMC)

Compensator Pressure Adjustment

Two Spool Load Sensing Compensators

Horse Power Compensator Functionality

Horse Power Pilot Cartridge

Troubleshooting Guide: Pump Performance

No Output Flow Issues

Troubleshooting steps for when the pump provides no output flow.

Motor Turns, Pump Does Not

Diagnosing issues when the motor turns but the pump does not.

Low Pressure with Full Flow

Identifying causes for low pressure output with full flow delivery.

Sticking at Zero Displacement

Troubleshooting steps for pumps stuck at zero displacement.

Pump Not Compensating

Diagnosing why the pump fails to compensate pressure or flow.

Compensator Instability

Parker PV180 Specifications

General IconGeneral
BrandParker
ModelPV180
CategoryWater Pump
LanguageEnglish

Related product manuals