Parkside PKO 270 A4 User Manual (English)

Other manuals for Parkside PKO 270 A4

Operating And Safety Instructions64 pages

Questions and Answers:

D
David BullockAug 18, 2025
What to do if my Parkside Air Compressor does not start?
- J
  Jeffrey HallAug 18, 2025
  If your Parkside Air Compressor isn't starting, several factors could be at play. First, check the supply voltage, power plug and the socket-outlet to ensure they are working correctly. Insufficient voltage could also be the issue, so ensure your extension cable isn't too long and has adequately sized wires. Also, the compressor may not start if the outside temperature is below +5° C. Finally, the motor may be overheated; allow it to cool down, and address the cause of overheating if necessary.
A
Alice KellyAug 21, 2025
Why does my Parkside Air Compressor start but there is no pressure?
- W
  Wesley AndrewsAug 21, 2025
  If your Parkside Air Compressor starts but doesn't build pressure, it could be due to a few reasons. The drain plug for condensation water might be leaking; try tightening it by hand and check the seal, replacing it if needed. Damaged seals could also be the culprit; inspect them and have them replaced by a service center.
T
Tiffany BrooksAug 23, 2025
What to do if my Parkside PKO 270 A4 Air Compressor starts but the tools don't?
- K
  Katrina PrattAug 23, 2025
  If your Parkside Air Compressor starts and shows pressure, but your tools aren't working, there are a couple of things to check. Ensure that the pressure set on the pressure regulator is sufficient; increase it if necessary. Also, check the compressed air hose and tools for any leaks and replace them if needed.
R
rbennettAug 26, 2025
What to do if my Parkside Compressor starts but tools don't?
- D
  Deborah WilsonAug 26, 2025
  If your Parkside Compressor starts, pressure is indicated on the pressure gauge, but the tools aren't working, first check the compressed air hose and tools for leaks, replacing them if necessary. Also, the pressure set on the pressure regulator may be insufficient. Try increasing the set pressure using the pressure regulator.
P
Pamela StevensAug 28, 2025
How to troubleshoot a Parkside Compressor that won't start?
- P
  Phillip SwansonAug 28, 2025
  If your Parkside Compressor doesn't start, begin by checking the supply voltage, power plug, and socket-outlet to ensure they are functioning correctly. Also, make sure the extension cable isn't too long and uses sufficiently large wires. Avoid operation below +5° C. If the motor is overheated, allow it to cool down and address the cause of overheating.
M
Michael HessAug 31, 2025
What to do if Parkside Compressor starts but no pressure?
- P
  paul54Aug 31, 2025
  If your Parkside Compressor starts but isn't building pressure, check the drain plug for condensation water and tighten it by hand. Inspect the screw's seal and replace it if needed.
M
Melissa DavidSep 2, 2025
Why is my Parkside Compressor starting but not building pressure?
- D
  dickersonnicoleSep 2, 2025
  If your Parkside Compressor starts but isn't building pressure, the seals might be damaged. A service center should check the seals and replace any damaged ones.
C
Craig WilliamsSep 4, 2025
Why won't my Parkside Compressor start in cold weather?
- M
  Max MorrisSep 4, 2025
  If your Parkside Compressor doesn't start due to low outside temperature, remember to never operate it when the outside temperature is below +5° C.
L
Lori ThompsonSep 7, 2025
What to do if Parkside Air Compressor starts but tools don't?
- S
  Samuel CunninghamSep 7, 2025
  If your Parkside Air Compressor starts but the tools aren't working, first check the compressed air hose and tools for leaks, replacing them if necessary. Also, a quick-lock coupling may have a leak. Finally, make sure the pressure regulator is set to a sufficient pressure and increase it if needed.
L
Leslie RaymondSep 10, 2025
How to troubleshoot Parkside Air Compressor that won't start?
- C
  Cristina GonzalesSep 10, 2025
  If your Parkside Air Compressor doesn't start, begin by checking the supply voltage, power plug, and socket-outlet. Also, ensure the extension cable isn't too long and has adequately sized wires. Avoid operating the compressor below +5° C, as low outside temperatures can prevent starting. Lastly, allow the motor to cool down, addressing any overheating causes.