What to do if my Parkside PWS 125 C3 doesn't start?
If your Parkside Grinder doesn't start, the issue might stem from a missing mains voltage or a tripped main circuit breaker. Check the socket, mains cable, and plug. If necessary, have a qualified electrician perform repairs. Also, inspect the main circuit breaker. Another potential cause is a defective on/off switch, which requires repair by Customer Care.
Why grinding disc does not rotate smoothly in Parkside PWS 125 C3 Grinder?
If the grinding disc of your Parkside Grinder does not rotate smoothly and you hear abnormal noises, the grinding disc nut may be loose. In this case, tighten the grinding disc nut. Another possible reason is that the grinding disc is defective, so you should replace it.
Why grinding disc does not rotate smoothly on my Parkside Grinder?
If the grinding disc of your Parkside Grinder does not rotate smoothly and you hear abnormal noises, first, ensure the grinding disc nut is tightened. If the issue persists, the grinding disc may be defective and needs to be replaced.
What to do if grinding tools do not move in Parkside Grinder?
If the grinding tools of your Parkside Grinder don't move even when the engine is running, it could be due to a loose grinding disc nut. Tighten the grinding disc nut. Alternatively, the drive might be blocked by the workpiece, remaining workpieces, or remaining grinding tools. Remove any blockages to resolve this.
Why does the engine slow down and stop on my Parkside Grinder?
If the engine of your Parkside Grinder slows down and stops, it may be overloaded by the workpiece. Reduce the pressure on the grinding tool. It may also be that the workpiece is unsuitable.
What to do if grinding tools do not move on my Parkside Grinder?
If the grinding tools on your Parkside Grinder aren't moving even though the engine is running, check if the grinding disc nut is loose and tighten it. Also, inspect for any blockages caused by the workpiece or grinding tools and remove them.
Why does the engine of my Parkside Grinder slow down and stop?
If your Parkside Grinder's engine slows down and stops, it might be overloaded by the workpiece. Try reducing the pressure on the grinding tool. The workpiece may also be unsuitable.
General| Power | 1250 W |
|---|---|
| Disc Diameter | 125 mm |
| No-load Speed | 11000 rpm |
| Rated Voltage | 230 V |
| Spindle Lock | Yes |
| Restart Protection | Yes |
| Spindle Thread | M14 |
Welcome and initial information about the purchased angle grinder.
Details the approved uses for cutting, scrubbing, and brushing metal, concrete, or tiles.
Specifies what the device should not be used for and its intended user base (DIY).
Covers user age, manufacturer liability, delivery contents, and function description.
Provides a numbered overview of the device's parts (Sections A, B, C, D).
Details technical specifications like voltage, power, speed, noise, and vibration levels.
Importance of reading instructions and basic safety measures for shock, injury, and fire prevention.
Explains how vibration values are measured and can vary based on usage and accessories.
Explanation of symbols found on the device and for personal protective equipment.
Covers maintaining a clean work area, avoiding explosive atmospheres, and electrical shock prevention.
Details symbols indicating usage restrictions and suitability for cutting discs.
Explains hazard, precaution, and notice symbols used within the manual.
Emphasizes staying alert, avoiding fatigue, and abstaining from substances while operating.
Stresses the importance of wearing safety glasses, dust masks, and protective footwear.
Ensures the power tool's switch is in the 'off' position before connecting to the power source.
Use the correct tool, verify switch operation, and disconnect power before adjustments.
Maintain balance, proper footing, and avoid loose clothing that can snag on moving parts.
Connect and properly use dust extraction systems to mitigate hazards from dust.
Use only manufacturer-approved accessories with correct rotation speed and dimensions.
Ensure threaded attachments fit the grinding spindle threading precisely.
Recommend servicing by qualified personnel using identical replacement parts.
Never use damaged tools; perform a run-in test to check for damage.
Wear face shields, goggles, dust masks, ear protection, and gloves as needed.
Ensure bystanders maintain a safe distance and wear PPE when in the work area.
Avoid contact with hidden wiring; keep cords away from rotating parts; do not use near flammable materials.
Never carry a running tool; place it down only after the attachment has stopped.
Clean ventilation slots; never use liquid coolants as they pose an electrical shock risk.
Connect to RCD-protected supply; keep cords away from discs; professional plug replacement.
Use correct speed discs, inspect visually, avoid sparks near people, and wear full PPE.
Prevent crushing by keeping fingers clear; hold workpiece firmly to avoid slipping.
Allow workpiece to cool; do not work when tired or under influence; take breaks.
Shutdown for blocked tools; identify residual risks like lung/hearing damage and EMF effects.
Hold tool firmly, position body, avoid corners, and never use prohibited attachment types.
Use only approved grinders and intended protective hoods for safe operation.
Ensure correct grinding wheel mounting and optimal protective hood adjustment for maximum safety.
Never use cutting discs sideways; avoid deep cuts; do not restart in workpiece without reaching speed.
Use correct, undamaged clamping flanges; inspect discs for wear and damage.
Use correct sandpaper sizes; ensure polishing bonnet strings are secure to prevent entanglement.
Be aware of wire loss; avoid overloading; ensure clearance between brushes and protective hood.
Use appropriate wheels for scrubbing; apply moderate pressure with correct angle.
Ensure sufficient space, no endangerment, and proper assembly of hoods/devices before use.
The handgrip must be mounted for operation; position it on left, right, or top threads.
Adjust the hood for spark direction and user safety; check adjustment nut tension.
Follow steps for installing discs, ensuring correct label orientation and secure clamping.
Use recommended accessories, ensure disc speed compliance, and never operate without protective equipment.
Keep hands clear of the disc during operation; ensure safe disc replacement practices.
Verify disc speed, dimensions, and integrity; use correct clamping flanges.
Ensure power supply voltage matches the device rating before connecting and operating.
Turn on the device, wait for max speed, and be aware the disc spins after shutdown.
Perform a trial run after installation or replacement to check for smooth operation and abnormal noises.
Disconnect power for maintenance; allow to cool; inspect for defects before each use.
Clean regularly with a soft cloth; avoid solvents and running water.
Detailed steps for replacing carbon brushes, ensuring proper installation of components.
Store appliance in a dry place; keep grinding discs dry and upright.
Return electrical machines to recycling centres; do not dispose of with domestic waste.
Addresses problems like device not starting, tools not moving, engine stopping, or abnormal noises.
Details how to obtain spare parts and accessories via website or Service Centre.
Lists specifications for cutting and flap discs, including item numbers and dimensions.
Provides specifications for sandpaper mounting plates and wire brushes.
Covers the 3-year guarantee period, proof of purchase, and user's statutory rights.
Explains how to submit a claim with defective equipment and a description of the defect.
Defines what is covered (material/manufacturing defects) and what is excluded (wear parts, misuse).
Have receipt and item number ready; contact service department for processing instructions.
Send products postage paid with proof of purchase and defect details; use provided service address.
Details paid repair services not covered by warranty, including cost estimates and submission requirements.
Provides contact information (phone, email) for service in Great Britain and Ireland.
Lists the importer's address; note that this is not a direct service address.
Confirms the angle grinder model meets applicable EU guidelines and directives.
Lists the harmonised standards used to ensure compliance with EU regulations.
States the declaration is issued solely under the manufacturer's responsibility.
To Next Page
