pcl D10 - User Manual

76376 Issue 5
www.pclairtechnology.com
D10 Inflator Quick Start Manual
Safety Guidelines
This manual contains information that is very important to know
and understand. This information is provided for safety and to
prevent equipment problems. To help recognise this information,
observe the following symbols.
Danger indicates an imminently hazardous
situation which if not avoided WILL result
in death or serious injury.
Warning indicates a potentially hazardous
situation which if not avoided, COULD
result in death or serious injury.
Caution indicates a potentially minor or
moderate injury.
Notice indicates important information,
that if not followed, may cause damage to
equipment.
Unpacking
After unpacking the unit, inspect carefully for any damage that
may have occurred during transit.
Do not operate unit if damaged during
shipping, handling or use.
General Safety Information
The operator of this product must take the necessary precautions
to prevent the level of danger indicated by these symbols. The
operator is required to read and understand this instruction
manual and all safety warnings, labels etc.
Any employer allowing the use of this product in their field of work
must distribute this instruction manual to all users. The employer
must also ensure all users read, understand and follow the
instructions as described in the manual, safety warnings, labels,
etc.
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
Image shown is PCL standard decal.
Actual decal may vary by individual part number.
Read and understand all safety warnings
and instructions before operating this
product. Failure to read and follow all
safety warnings may result in serious
personnel injury or death. Property
damage and/or product damage may also
occur if all warnings are not followed.
1. Do not expose the product to flammable gases,
vapours or fumes
2. Do not store flammable gases in or near this product
3. Never use flammable or toxic solvents to clean the
product or any of the unit's parts
4. Never remove or alter any safety warning labels, tags,
etc. located or provided with product.
5. Follow all directions for maintenance.
The use of other than genuine PCL
replacement parts may result in reduced
equipment performance. Repairs must be
performed by authorised repair personnel,
otherwise the warranty will be void.
PART NUMBER
SERIAL NUMBER

Summary

Safety Guidelines and Symbols

DANGER Symbol

Indicates an imminently hazardous situation resulting in death or serious injury if not avoided.

WARNING Symbol

Indicates a potentially hazardous situation resulting in death or serious injury if not avoided.

CAUTION Symbol

Indicates a potentially minor or moderate injury.

NOTICE Symbol

Indicates important information that may cause equipment damage if not followed.

Unpacking and General Safety

Warning on Damaged Unit

Do not operate unit if damaged during shipping, handling, or use.

Operator and Employer Responsibilities

Operators must understand manual; employers must distribute it to all users.

General Operating Warnings

Read and understand all safety warnings and instructions before operating the product.

General Specifications and Control Panel

General Specifications

Details max inlet supply, recommended supply, max/min operating pressure, and units.

Control Panel Overview

Identifies buttons, ports, and indicators on the control panel.

Installation and Calibration

Installation Requirements

Covers power supply, air supply, mounting, and grounding for safe installation.

Calibration and Accuracy

Specifies the maximum permissible error (MPE) and its traceability.

Hose Connection Notice

Use two spanners to tighten hose connections, holding filter housing to prevent spinning.

Start-up and Operation

Start-up Procedure

Steps for powering on the unit, display checks, and initialisation.

Standard Operation: Inflation;Deflation

Process for setting pressure, connecting to tyre, and automatic inflation/deflation.

Tyre Wear Inspection Warning

Inspect tyres for wear or damage; do not inflate suspect tyres.

User Inspection Mode

How to access and use the unit as a pressure gauge; inflator cycle is inhibited.

Service, Maintenance, and Safety

Service and Maintenance

Details non-serviceable items, periodic checks, and procedures for faulty components.

Working Safety Instructions

Guidance on explosion hazards, product danger, approved usage, and general precautions.

Troubleshooting and Error Messages

Common Problems and Solutions

Lists common issues like no display, buzzer faults, and their respective solutions.

Error Code Explanations

Details error codes E1-E23, their causes, and required actions like sensor/PCB replacement.

PCL Limited Warranty and Registration

PCL Limited Warranty Details

Covers warranty period, exclusions, claim procedure, and liability limitations.

Warranty Registration Process

Instructions for mailing a form or registering online to activate the warranty.

Calibration Certificate Information

Calibration Procedure

Details that units are checked and calibrated on traceable equipment before release.

EC Directives Compliance

States compliance with EMC and Low Voltage EC directives, listing relevant standards.

pcl D10 Specifications

General

Brand	pcl
Model	D10
Category	Power Tool
Language	English