Peavey BACKSTAGE 50

SO WATTS
20V BMS
8 OHMS
120 VAC
CO Hi
150 WATTS
CAUTION
TO P‘1 EVEN! TVP R6K CP FIRF AtHS^SCK HAZARD.
CO HOT fXFOlf TRS APfUSNtS TO R4fc OR
MOISTURE DO*JOTnr*.OVUFiia.VCftSfc- UCU3ER
sewceABte pacts tvsice heferservcno to
QUAIIHBJ SERVICE PERSOItNiL
AVIS msa« nr. a-oc fiecrRiae fas
ccwrir
BACKSTAGE, 50
MADE IN U.SA
FOOT SWITCH
APRCOUCTTf Ff«VFV FI FCTfO'JKSCOF.P
MERIDIAN MS
PATENT CEriaNS
15
16
LINE CORD (15)
(120V products only)
For your safely, we have in¬
corporated a 3-wire line (mains)
cable with proper grounding
facilities. It is not advisable to
remove the ground pin under any
circumstances. If it is necessary to
use the equipment without proper
grounding facilities, suitable
grounding adaptors should be used.
Less noise and greatly reduced
shock hazard exists when the unit is
operated with the proper grounded
receptacles.
KEMOTE SWITCH JACK (16)
Provided for the connection of the
optional remote foots witch. Foot-
switch is used to select the Lead or
Normal channels and defeat reverb.
When using remote footswitch,
always insert the plug fully (second
click) to ensure proper operation.
LINE CORD (15)
(120V products only)
(nur bei 120 Volt-Geraten)
Zu lhrer Sicherhcit haben wir das
Ccrat mit oinom dreiadrigen geerde-
ten Netzkabel versehen. Esistunter
keincn Umstanden empfehlenswert
den Erdungskontakt des AnschluB-
kabels zu losen. Falls es notwendig
sein sol lie, das Equipment ohne die
vorgesehene Erdung ?.u betreiben
empfichlt sich die Verwendung
cincs Grounding Adaptors. Die ge-
ringsten Storgerausche unddic hoch-
sicSichcrhpit vorelektrischenSchla-
gen wird jcdoch durch die Benut-
zung der vorgesehenen Erdungsmog-
lichkeiten erreicht.
REMOTE SWITCH JACK (16)
(Remote Switch Jack)
Vorgesehen fur den AnschluS des
als Option erhalllichen Fufischal-
ters. Der Fufischalter kann zum
Anwahlen des Normal- und Lead-
kanals sowic zum Scholtcn des
Halls verwendet werden. Um eine
cinwandfreie Funktion zu gewahr-
leisten, ist beim AnschluB des Full-
schalters darauf zu achten.dafi der
Steeker vollstandig (bis /.um 2.
Klick) eingestecki ist.
LINK CORD (15)
(Cordon secteur)
Cet appareil est cquipc d’unc fiche
secteur a 3 broches nvee misc & la
terre. 1-a mise a la terre diminuc le
bruit de fond et assure la serurite
ntfeessaire ft l’emploi decet appraeil
dlcctrique.
REMOTE SWITCH JACK (16)
(Rrise pour interrupteur a dis¬
tance)
Cette prise recoil In fichede la pfdale
interrupteur (en option). Les inter-
rupteurs au pied ont. pour fonctions
lc choix du canal on service (Lead ou
Normal) et la m isc en ou hors service
do la Reverberation. Veiller a bien
enfoncer la fiche ft fond dans la
pri*e jusqu’au deuxiOme cran.
LINE CORD (15)
(120 V Solamente)
Para su protecion hemos incor-
porado un cable do 3 alambres con
tierra. No es recomendable el re¬
mover la patadetierra bajoninguna
cireumstancia, se reoomienda un
adaptador en caso necesario. Esto
reducira ruidos y peligrosos cor-
rientazos.
REMOTE SWITCH JACK (16)
(Entrada para el sw itch de con¬
trol rcnioto)
Prevista para lc concxion del pedal
remoto opcional. El switch del pedal
es usado paraseleccionarelreqinntn
o ol canal normal y para desactivar
la reverberad6n.Cuandoeste usan-
do ul pedal remoto inserteelconecior
completamente (hasta el segundo
click) para asegurar su correcta
opcrocion.
BACKSTAGE 50 ENGINEERING SPECIFICATIONS
POV/EF AMPLIFIER SECTION:
RATED POWER & LOAD:
50W RMS into 8 ohms
POWER @ CLIPPING: (Typically)
(5% THD, 1 kHz. 120 VAC line)
55W RMS into 8 ohms
4 ohms not recommended
FREQUENCY RESPONSE:
+0, 2 dB 60 Hz to 20 kHz @ 45 watts into 8 ohms
TOTAL HARMONIC DISTORTION:
Less than 0.3%, 100 mW to 45W RMS.
60 Hz to 10 kHz, 8 ohms
Typically below 0.2%
HUM & NOISE:
Greater than 90 dB below rated power
POWER CONSUMPTION:
150 waits. 50/60 Hz. 120 VAC
PREAMP SECTION:
The following specs are measured @ 1 kHz with the controls
preset as follows:
Push Bright (Off/Out)
Channel Select (Norm/Out)
Supersat’* @ 10
Post Gain (2) 10
Low & High EQ @ 10
Mid EQ@0
Reverb @ 0
Nominal levels are with Normal Gain level @ 5
Minimum levels are with Normal Gain level @ 10
PREAMP HIGH GAIN INPUT:
Impedance: High Z, 220K ohms
Nominal Input Level: -20 dBV, 100 mV RMS
M nimum Input Level 36 dBV, 15 mV RMS
Maximum Input Level: +4 dBV, 1.5 V RMS
PREAMP LOW GAIN INPUT:
Impedance: High Z. 44K ohms
Nominal Input Level: -14 dBV. 200 mV RMS
Minimum Input Level: -30 dBV. 30 mV RMS
Maximum Input Level: +10 dBV, 3 V RMS
EFFECTS SEND:
Load Impedance: 10K ohms or greater
Nominal Output: -10 dBV. 0.3 V RMS
EFFECTS RETURN:
Impedance: High Z, 22K ohms
Designed Input Level: -10 dBV, 0.3 V RMS
(Switching jack providing effects send to effects return
connection when not used)
HEADPHONE OUTPUT:
Load Impedance: 4 ohms or greater
Nominal Power Output: 100 mW into 4 ohms
(Stereo jack, monaural signal, disconnects
internal speaker when phono plug is inserted)
SYSTEM HUM & NOISE @ NOMINAL INPUT LEVEL:
(20 Hz to 20 kHz unweighted]
72 dB below rated power
EQUALIZATION:
Special Low, Mid & High passive-type EQ
Automatic thick EQ when lead channel selected
Push Bright: +6 dB @ 2 kHz
EXTERNAL FOOTSWITCH FUNCTION:
Reverb defeat (When reverb control raised)
Lead Channel defeat (When selected with button)