Frequency Response:
52 Hz – 20 kHz
Low Frequency Limit (-3 dB point):
60 Hz
Usable Low Frequency Limit (-10 dB point):
52 Hz
Internal Power Amplifiers:
Woofer - 1200 watts peak available power
Continuous Power: 450 watts @ less than 1% distortion
Tweeter - 150 watts peak available power
Continuous Power: 75 watts @ less than 1% distortion
Nominal Sensitivity (1W @ 1M, Swept Sine Input in Anechoic
Environment):
100 dB (average)
Maximum Sound Pressure Level:
131 dB music peak
Nominal Radiation Angles:
100˚ horizontal by 30˚ vertical
Transducer Complement:
15"
®
Black Widow® woofer, Model 1508-4 DPE and RX™22CT
compression driver tweeter
Box Tuning Frequency (FBOX):
61 Hz
Electoacoustic Crossover Frequency:
2,000 Hz
Crossover Type:
Internal DSP-controlled Electronic two-way crossover with driver
EQ, level matching, bass boost and subsonic filtering
Crossover Slopes:
24 dB/octave (Fourth order) low pass, 24 dB/octave (Fourth
order) high pass, both with staggered poles and driver EQ. Unit
has horn spatially aligned with woofer, so there is no need for
phase alignment or time delay of the signals.
Electronic Input Impedance (NOMINAL):
10 k ohms unbalanced
20 k ohms balanced line level
24 k ohms balanced mic level
Input Connections:
Input 1:
One combo female XLR/ 1/4" phone jack providing balanced
operation, with switch-selectable mic- or line-level sensitivity
Input 2:
One combo female XLR/ 1/4" phone jack providing balanced
operation, with switch-selectable mic- or line-level sensitivity.
Two RCA phono-type jacks, which are buffered and mixed to
monophonic for a summed signal. These are NOT a stereo input,
as the DPE™ 2P-4P is a single full-range sound source.
Output Connections:
One male XLR balanced output, one 1/4" TRS balanced
phone-type jack.
Cabinet Material:
Wood
Mounting:
Subwoofer pole-mounting or speaker stand, and 4 rubber feet for
floor or stage use.
DImensions (H x W x D)
DPE-2P:
29.25" (74.3 cm) x 18.75" (47.6 cm) x 16.88" (42.9 cm)
DPE-4P:
46.13" (117.2 cm) x 18.75" (47.6 cm) x 16.88" (42.9 cm)
Net Weight:
DPE 2-P: 67.0 Lbs. (30.5 kg)
DPE 4-P: 103.0 Lbs. (46.7 kg)
ELECTRONICS AND AMPLIFIER SPECIFICATIONS
Electronic Input Impedance (NOMINAL):
Balanced inputs: 20 k ohms line level sensitivity selected, 2.4 k
ohms mic level sensitivity selected
Mic Switch Sensitivity Increase:
30 dB
Push-button EQ modes of DynaQ
™
:
Flat Frequency Response
Filtered roll-off of high and low frequencies (Speech Mode)
Dynamic boost to high frequencies (Contour)
Dynamic boost to both high and low frequencies,
(Fletcher-Munson type compensation, Contour and Bass
Enhancer)
Nominal Amplifier Frequency Response:
0+, -1 dB from 10 Hz to 20 kHz
Hum and Noise:
Greater than 90 dB below rated power
DDT
™
Dynamic Range:
Greater than 22 dB
THD and IM:
Typically less than 0.1%
Damping Factor:
Greater than 100 @ 1000 Hz, 8 ohms
Power Requirements of Peavey DPE 2P-4P System:
Nominal 700 watts
DPE
™
2P - 4P SPECIFICATIONS
To Next Page
Loading...
