Peavey TMax - Technical Specifications; Power Amp and Input Specifications; Preamp, Signal Levels, and EQ

7
SPECIFICATIONS
POWER AMP SECTION
Power Output with DDT™
Compression Active:
200 W RMS into 8 ohms
350 W RMS into 4 ohms
500 W RMS into 2 ohms
Input Sensitivity:
Input signal necessary for full
output = 1.7 V RMS
DDT™ Dynamic Range:
Greater than 20 dB
DDT™ Maximum THD:
Below 0.6% THD for 6 dB overload
Below 1% THD for 16 dB overload
Hum & Noise:
Greater than 95 dB below rated
power
Power Consumption:
Domestic: 900 watts @ 120 V AC,
60 Hz
Export: 900 watts @ 220-240 V AC,
50/60 Hz
PREAMP SECTION
All measurements are with the follow-
ing settings except where noted.
Note: Tube channel is designed to
produce distortion when pre
gain control is set greater than
3 (dependent on input signal).
Note: All signals referenced to
1 V RMS = 0 dB.
Solid-State Pre Gain @ 5
Master Volume @ 5
-10 dB Pad Out
All EQ Sliders @ 0 (Centered)
Low and High Shelving @ 0
Input Signal Levels:
Solid-State Channel, -10 dB
Pad Out
Nominal Input: 0.14 V RMS,
-17 dB
Minimum Input: 16 mV RMS,
-36 dB
Maximum Input: 2.0 V RMS,
+6 dB
Solid-State Channel, -10 dB
Pad In
Nominal Input: 0.422 V RMS,
-7.5 dB
Minimum Input: 50 mV RMS,
-26 dB
Maximum Input: 6.0 V RMS,
+15.5 dB
Tube Channel, -10 dB Pad
Out, Post Gain @ 5
Nominal Input: 0.054 V RMS,
-25.3 dB
Minimum Input: 5 mV RMS,
-46 dB (Post Gain @ 10)
Maximum Input: 1.0 V RMS,
+0 dB (For Clean Signal)
Tube Channel, - 10 dB Pad In
Nominal Input: 0.160 V RMS,
-16 dB
Minimum Input: 15 mV RMS,
-36.5 dB (Post Gain @ 10)
Maximum Input: 3 V RMS,
+9.5 dB (For Clean Signal)
Effects Loop (Post EQ):
Send Level (High Setting): -7 dB
Send Level (Low Setting): -15 dB
Return Level (High Setting): -7 dB
Return Level (Low Setting): -15 dB
Crossover:
Low Output Levels:
Nominal: 1.7 V RMS, 4.6 dB
Maximum: 8 V RMS, +18 dB
High Output Levels:
Nominal: 1.7 V RMS, 4.6 dB
Maximum: 8 V RMS, +18 dB
Full Range Output Levels:
Nominal: 1.7 V RMS, 4.6 dB
Maximum: 8 V RMS, +18 dB
Frequency:
Variable from 100 Hz to 1 kHz
Balanced Out:
Pre EQ: -1.35 dB from input jack,
-20 dB from full range output
(-10 dB Pad Out)
Post EQ: -7 dB nominal, +15.5 dB
maximum
Note: Post EQ balanced output taken
before master volume, Pre EQ
balanced output buffered off
input jack.
Equalization:
Graphic Equalizer: ±15 dB @ 40,
100, 250, 625, 1.6 K, 4 K, 10 K
Shelving Controls:
±15 dB high shelving @ 8 kHz
±15 dB low shelving @ 20 Hz