Peco TA180 - User Manual

TA/TB180 THERMOSTAT
READ THESE INSTRUCTIONS CAREFULLY BEFORE
ATTEMPTING TO INSTALL, OPERATE OR SERVICE THIS
THERMOSTAT.
Failure to observe safety information and comply with instruc-
tions could result in PERSONAL INJURY, DEATH AND/OR
PROPERTY DAMAGE.
To avoid electrical shock or damage to equipment, disconnect
power before installing or servicing and use only wiring with
insulation rated for full thermostat operating voltage.
Before installing this control, the Voltage Selection Switch must
be placed in the correct position. See instructions.
To avoid potential re and/or explosion do not use in potentially
ammable or explosive atmospheres.
Retain these instructions for future reference. This product,
when installed, will be part of an engineered system whose
specications and performance characteristics are not designed
or controlled by PECO. You must review your application and
national and local codes to assure that your installation will be
functional and safe.
•
•
•
•
•
•
WARNING
CAUTION
Use copper wire only, insulate or wire nut all unused leads.
Care should be used to avoid electrostatic discharge to the T180
thermostat.
This unit has conguration jumpers. You may need to recongure
this thermostat for your application.
APPLICATIONS AND FEATURES
For 2 or 4 Pipe Fan Coil and On/Off Control Applications
7 Day, 4 Event Programmability
System Selection: Off-Heat-Cool-Auto-Setback
6 Outputs: 1H, 1C, Up to 3 Fan, OA Damper
Fan Control: 1-3 Speeds
Cycling (Auto) or Continuous (On)
Automatic Fan Speed Staging (TB180 models only)
Connections for:
Fan Coil Pipe Sensor
Remote Temperature Probe
Occupancy Control
Door Switch or Setback
Condensate Overow
SPECIFICATIONS
Temperature Set Point Range 50 to 90°F / 10 to 32°C
Differential 1°
Memory – Back-Up EEPROM, No batteries required,
Stores settings for unlimited time
Mounting Installs on standard 4” x 4”
device box with a 2” x 4”
horizontal mud ring
•
•
•
•
•
•
•
•
•
•
•
•
▲
!
Physical Dimensions 4.4”H x 5.8”W x 1.1”D
Agency Approvals UL, UL Canada
Electrical Ratings (see table below)
RATINGS
VOLTAGE
RES
AMPS
PILOT
DUTY
HP
24 VAC NA NA NA 24 VA NA
FLA LRA
120 VAC 5.8 34.8 6.0 125 VA 1/4
240 VAC 2.9 17.4 5.0 125 VA 1/4
277 VAC 2.4 14.4 4.2 125 VA 1/4
COMBINED LOAD CURRENT NOT TO EXCEED 20 AMPS
INSTALLATION
New Installations
The thermostat should be used indoors only. It should be mounted on
an inner wall in a location with freely circulating air, and where it will be
responsive to changes in room temperature. Avoid mounting near heat
generating appliances (i.e. TV, heater, refrigerator), or in direct sunlight.
Remove Old Thermostat
Turn off power to thermostat at main fuse or circuit breaker box.
Ensure that ALL power is disconnected. To prevent electrical
shock and /or equipment damage, disconnect electrical
power to the system at the main fuse or circuit breaker until
installation is complete.
Remove the front cover of old thermostat. With wires still attached,
remove wall plate from the wall. If the old thermostat has a wall
mounting plate, remove the thermostat and the wall mounting plate
as an assembly.
Before removing wires from old thermostat, label each wire
with the terminal designation from which it was attached.
Disconnect the wires from the old thermostat one at a time. Do not
let wires fall back into the wall.
Jumper and Circuit Board Selections
Voltage Selection Switch: This switch must be placed in the appropriate
position prior to application of power.
24V = 24 VAC
110-277 V = 120, 240 or 277 VAC
JP1 Jumper Selection – Remote Temperature Sensor:
Local Sensing – Install JP1
Remote Sensing – Remove JP1 – Accessory sensors are available
in standard 60” lengths but can be extended to meet application
requirements.
1.
2.
3.
4.
•
•
•
•
© COPYRIGHT 2008 PECO, INC. ALL RIGHTS RESERVED. P/N 69387 3220-2124 REV 0 PAGE 1
▲
!
▲
!
SYSTEM FAN PROGRAM
▲
!

Peco TA180 Specifications