To Next Page
D
Deborah FordSep 23, 2025
What does F40 error mean on Pelgrim GVW250L/P03?
- NNancy GaySep 23, 2025
F40 error on your Pelgrim Dishwasher indicates an inlet valve leakage. Turn off the water tap.
What does F40 error mean on Pelgrim GVW250L/P03?
F40 error on your Pelgrim Dishwasher indicates an inlet valve leakage. Turn off the water tap.
Why does my Pelgrim Dishwasher leave spots on stainless steel or silver?
If spots appear on stainless steel or silver items washed in your Pelgrim Dishwasher, it could be due to certain foods like mustard or lemon being left on items for too long; rinse these off before washing. Also, different metals in contact during washing can cause spots, so separate silver, stainless steel, and aluminum items. Check and adjust the rinse aid dosage. If using all-in-one detergent, consider switching or adding separate rinse aid and salt. Ensure the salt compartment is full and the water softener setting is correct. Also, make sure the salt compartment lid is properly tightened.
What to do if water remains in my Pelgrim GVW250L/P03 after cycle?
If your Pelgrim Dishwasher has water remaining after a cycle, the filters might be clogged; clean the coarse and fine filters. Ensure the filters are correctly fitted. Check for debris in the drainage pump and ensure the yellow drainage pump stop is in place. Inspect the drainage hose for kinks or blockages; disconnect it from the sink unit's water trap to check for obstructions, ensuring the connection has an inner diameter of at least 14 mm.
How to get rid of bad odour in Pelgrim GVW250L/P03?
If your Pelgrim Dishwasher has a bad odor, clean around the seals and in corners with a washing-up brush and low foaming cleaner. If you've been using low temperature programs for a long time, run a program with a high temperature once or twice a month, or use the self-cleaning program.
What does F41 error mean on Pelgrim Dishwasher?
F41 error on your Pelgrim Dishwasher indicates a heater fault. Turn off the water tap and remove the plug from the wall socket.
What to do if my Pelgrim GVW250L/P03 cannot close door?
If you're having trouble closing the door of your Pelgrim Dishwasher, make sure the baskets are correctly positioned horizontally. Also, check that the dishes aren't blocking the baskets from sliding properly into place.
What causes grease deposits in the Pelgrim Dishwasher?
Grease deposits can form in your Pelgrim Dishwasher if you've been using low-temperature programs for a long time. To resolve this, select a high-temperature program like Intensive 70° to dissolve the grease, or run a self-cleaning program.
How to stop my Pelgrim Dishwasher from overfilling with water?
To address overfilling in your Pelgrim Dishwasher, clear the drainage pump. If the problem continues, contact your nearest service center.
Why does the control panel of my Pelgrim GVW250L/P03 not react?
If the control panel of your Pelgrim Dishwasher doesn't respond when pressed, wait a moment and try again, especially if you've just opened the door. Ensure the door is open, as the control panel only works when the door is open. Also, clean the control panel with a dry or slightly damp cloth to remove any dirt.
How to fix the door lock if it does not click into place on my Pelgrim Dishwasher?
Check the door lock on your Pelgrim Dishwasher. If it doesn't click into place, open the door, press and hold the Automatic door opening button until the display counts down, wait until the countdown ends (60 seconds), and then close the door again to ensure the lock engages.
General| Brand | Pelgrim |
|---|---|
| Model | GVW250L/P03 |
| Category | Dishwasher |
| Language | English |
