Pfaff 3307-3 Series - User Manual

To Next Page

INSTRUCTION MANUAL

296-12-19 035/002

Betriebsanleitung engl. 06.09

This instruction manual applies to machines from the

following serial numbers 2 752 431 and software

version 0366/001 onwards:

3307-3/..

3307-9/..

Industrial

Main Page

Table of Contents3
Safety7
Regulations7
General Notes on Safety7
Safety Symbols8
Important Notes for the User8
Notes for Operating and Technical Staff9
Operating Staff9
Technical Staff9
Danger Warnings10
Proper Use11
Speciﬁ Cations12
General Information12
Seam Pattern Sizes13
Disposal of Machine14
Transportation, Packing and Storage15
Transportation to Customer's Premises15
Transportation Inside the Customer's Premises15
Disposal of Packing Materials15
Storage15
Explanation of Symbols16
Controls17
Main Switch17
Pedal17
Balance Wheel18
Special Operating Elements of the PFAFF 3307-318
Adjusting the Button Clamp18
Lock Lever of the Blind Stitching Guide19
Setting the Stem Lengths19
Setting the Penetration Depth20
Missed Stitch Detection Key20
Special Operating Elements of the PFAFF 3307-9/0121
Setting the Stem Length21
Control Panel21
Screen Displays22
Display Symbols22
Function Keys22
Adjusting the Table Height25
Mounting and Commissioning the Machine25
Installation25
Drilling Template for the Table-Top26
Connecting the Plug-In Connections and Earth Cable27
Fitting the Reel Stand28
Commissioning28
Switching the Machine on / off28
Setting the Seam Pattern Size29
Establishing the Value for Parameter "20429
Altering Parameter "20430
Setting up31
Inserting the Needle31
Threading the Sewing Thread32
Special Setting-Up Work on the PFAFF 3307-333
Selecting the Button Type and Program Number33
Adjusting the Button Clamp to the Button Size34
Selecting the Stem Length34
Setting the Stem Length for the Short Stem35
Setting the Stem Length for the Long Stem35
Selecting/Setting the "Sew-Through Button Attachment" Function36
Selecting/Setting the "Blind Sewing" Function36
Selecting/Setting the "Blind Sewing through the Facing" Function37
Allocating the Stem Length to the Seam Version38
Loading Plate for Loading Stay Button38
Special Setting-Up Work on the PFAFF 3307-939
Setting the Stem Length39
Inserting and Removing the SD-Memory Card39
Activating the Sequence Mode40
Sewing42
Sewing with the PFAFF 3307-343
Sewing with the PFAFF 3307-945
Error Messages46
Input47
Seam Pattern Input on Machines from Subclass -347
Seam Pattern Input for Two-Hole and Self-Shank Buttons47
Seam Pattern Input for Three-Hole Buttons48
Seam Pattern Input for Four-Hole Buttons49
Seam Pattern Input for Six-Hole Buttons50
Seam Pattern Input on Sub-Class -953
Sequence Input54
Program Management55
Calling up the Program Management56
Displaying Programs in the Machine Memory57
Displaying Programs on the SD-Memory Card58
Copying Programs to the SD-Memory Card59
Copying Programs to the Machine Memory60
Deleting Programs in the Machine Memory61
Deleting Programs on the SD-Memory Card62
Formatting the SD-Memory Card63
Care and Maintenance64
Maintenance Intervals64
Cleaning the Machine64
Cleaning the Hook Compartment65
Cleaning the Air Fi Lter/Lubricator65
Checking/Adjusting the Air Pressure66
Top up the Oil for Needle Drive66
Topping up Oil for the Gears67
Lubricating the Gear Shaft67
Adjustment68
Notes on Adjustment68
Tools, Gauges and Other Accessories68
Abbreviations68
Toothed Belts of the Main Drive69
Top Needle Bar Position (Reference Position)70
Pre-Adjusting the Needle Height71
Position of the Needle to the Needle Hole72
Basic Position "Button Clamp Raised73
Sensor Board of the Needle Drive (in Dismantled Condition)74
Basic Setting of the Needle Drive76
Position of the Hook Shaft to the Needle77
Adjusting the Drag Link Mechanism78
Needle Rise and Hook Clearance79
Readjusting the Needle Height81
Adjusting the Loop Spreader82
Position of the Loop Spreader to the Needle83
Adjusting the Thread Trimmer on the PFAFF 3307-384
Manual Cutting Test (Only on the PFAFF 3307-385
Adjusting the Thread Catcher (Only on the PFAFF 3307-386
Adjusting the Thread Loop Support on the PFAFF 3307-387
Adjusting the Spreader (Only on the PFAFF 3307-988
Adjusting the Thread Loop Support on the PFAFF 3307-989
Aligning the Button Holder (Only on the PFAFF 3307-990
Basic Position of the Button Holder (Only on the PFAFF 3307-991
Adjusting the Thread Trimmer on the PFAFF 3307-992
Basic Position of the Button Clamp Drive on the PFAFF 3307-393
Basic Position of the Button Clamp Drive on the PFAFF 3307-994
Aligning the Button Clamp (Only on the PFAFF 3307-3/01)95
Adjusting the Clamp Pressure (Only on the PFAFF 3307-396
Basic Setting of the End Knotting Equipment97
Adjusting the Retaining Fi Nger of the End Knotting Equipment98
Adjusting the Lifting Lever of the End Knotting Equipment99
Adjusting the Reed Switch100
Setting the Angle for the End Knotting101
Adjusting the Moment Tension102
Adjusting the Thread Puller103
Adjusting the Thread Clamp104
Adjusting the Thread Regulator105
Adjusting the Thread Wiper106
Adjusting the Thread Air Jet107
Aligning the Holder of the Blind Stitching Guide (Only on the PFAFF 3307-3/01)108
Basic Position of the Blind Stitching Guide (Only on the PFAFF 3307-3/01)109
Adjusting the Height of the Mounting Plate (Only on the PFAFF 3307-3/01)110
Basic Position of the Stay Button Plate (Only on the PFAFF 3307-3/01)111
Adjusting the Insert Plate (Only on the PFAFF 3307-3/01)112
Adjusting the Reed Switch for the Insert Plate (Only on the PFAFF 3307-3/01)113
Insert Plate Pressure (Only on the PFAFF 3307-3/01)114
Adjusting the Stem Fi Nger (Only on the PFAFF 3307-3/01)115
Parameter Settings118
Selecting the Function Group and Altering the Parameter118
Entering / Altering the Access Code119
Allocating Access Rights120
Parameter List121
Description of the Error Messages128
Sewing Motor Errors130
Internet Update of the Machine Software131
Update with Null Modem Cable131
Update with SD-Card132
Wearing Parts134
Pneumatics-Switch Diagram135
Circuit Diagrams138

Brand	Pfaff
Model	3307-3 Series
Category	Sewing Machine
Language	English

Pfaff 3307-3 Series - User Manual

Table of Contents

Pfaff 3307-3 Series Specifications

Related product manuals