Pfister Masey 8P8-WS2-MCS

To Next Page

Required Tools

Herramientas necesarias

Outils nécessaires

Additional Helpful Tools

Otras herramientas útiles

Outils supplémentaires utiles

Telon Tape

Cinta de telón

Ruban en télon

Parts in the Box • Piezas en la caja • Pieces dans la boîte

Turn O Water Supply • Cierre el suministro de agua • Couper l’alimentation en eau

Adjustable Wrench

Llave ajustable

Clé réglable

Phillips Screwdriver

Destornillador de estrella

Tournevis Phillips

500320300

December 20, 2018

Installation Support • Soporte de instalación • Support d’installation

Installation Videos Available

Videos de instalación a disposición

Vidéos d’installation disponibles

pisterfaucets.com/videos

Safety Goggles

Anteojos de seguridad

Lunettes de sûreté

Quick Installation Guide

Guía de instalación rápida

Guide d’installation rapide

8P8WS2MCS

Masey

™

Tub & Shower Trim

Borde para bañera y ducha

Garniture de baignoire et douche

To reduce the risk of injury or property damage, read all instructions before installing product. Wear safety goggles. Product must be

installed in accordance with all state & local plumbing & building codes. Call a professional if you are uncertain about installing this product.

This product has been designed for use with the Pister™ 0X8 Series Pressure Balancing Valve. It will not work with any other product valve.

Please review the 0X8 valve installation instructions before installing this product.

Para disminuir el riesgo de lesiones o daños a la propiedad, lea todas las instrucciones antes de instalar el producto. Utilice gafas de seguridad.

El producto deberá instalarse de acuerdo con la normativa de plomería y construcción estatal y local. Llame a un profesional si no está seguro

sobre cómo instalar este producto. Este producto ha sido diseñado para usar con la válvula de equilibrio de presión de la Serie 0X8 de Pister™. No

funcionará con cualquier otra válvula. Revise las instrucciones de instalación de la válvula 0X8 antes de instalar este producto.

Pour réduire le risque de blessures ou de dommages, lire toutes les instructions avant d’installer l’appareil. Porter des lunettes de sécurité. Il faut

installer l’appareil en respectant tous les codes de construction et de plomberie locaux et d’État. Appelez un professionnel si vous n’êtes pas certain

de la façon d’installer cet appareil. Cet appareil a été conçu pour être utilisé avec la valve d’équilibrage de pression Pister™ OX8. Il ne fonctionnera

pas avec la valve d’un autre appareil. Veuillez lire les instructions d’installation de la valve OX8 avant d’installer ce produit.

WARNING / ADVERTENCIA / AVERTISSEMENT

Locate the water supply inlets & shut o the water supply valves. These are usually found near the water meter.

If you are replacing an existing unit, remove the old unit & clean mounting surface thoroughly.

Ubique las entradas del suministro de agua y cierre las válvulas de suministro. Estas se encuentran generalmente cerca

del medidor de agua. Si reemplaza una unidad existente, retírela y limpie completamente la supericie de montaje.

Repérez les entrées d’alimentation d’eau et fermez les robinets d’arrêt. Ils sont normalement trouvés près du compteur

d’eau. Si vous remplacez un appareil existant, enlevez le vieil appareil et nettoyez soigneusement la surface de montage.

Personal Assistance, Product Specs, &

“How-to” Questions:

Asistencia personal, especiicaciones del

producto y preguntas sobre “cómo hacerlo”:

Aide personnelle, spéciications du produit

et questions « pratico-pratiques » :

1800PFAUCET (7328238)

pisterfaucets.com/support

1284001

Separate instructions supplied

Instrucciones que son incluidas

Instructions qui sont inclus

Flashlight

Linterna

Lampe De Poche

Cloth

Paño de limpieza

Chion

Supplied Hex Wrench

Proveído Llave hexagonal

Fourni Clé hexagonale

SAMPLE COPY

Main Page

Need help?

Do you have a question about the Pfister Masey 8P8-WS2-MCS and is the answer not in the manual?

This document is a Quick Installation Guide for the Pfister Masey™ 8P8-WS2-MCS Tub & Shower Trim, a plumbing fixture designed for bathrooms. It provides instructions in English, Spanish, and French for installing and using the product.

Function Description:

The Pfister Masey™ 8P8-WS2-MCS is a tub and shower trim kit. Its primary function is to control the flow and temperature of water to both a bathtub spout and a showerhead. It is designed to work exclusively with the Pfister™ OX8 Series Pressure Balancing Valve, which is a critical component for maintaining consistent water temperature and preventing scalding. The trim kit includes a handle for water control, a shower arm, a showerhead with multiple spray functions, and a tub spout.

Important Technical Specifications:

Model: Masey™ 8P8-WS2-MCS
Product Type: Tub & Shower Trim
Compatibility: Exclusively designed for use with Pfister™ OX8 Series Pressure Balancing Valve. It will not work with any other product valve.
WaterSense® Certified: Meets EPA Criteria and is certified by IAPMO R&T, indicating water efficiency.
Installation Requirements: Must be installed in accordance with all state and local plumbing and building codes.
Mounting Surface: Requires a clean mounting surface for installation.
Work Area Dimensions (Tub & Shower):
- 30" (76 cm) diameter clearance around the handle.
- 48" (122 cm) diameter clearance for the shower arm and showerhead.
- Minimum 8" (203 mm) clearance from the tub spout to the wall.
- 1¼" (32 mm) diameter hole for the handle.
- 4¾" (121 mm) diameter for the escutcheon, or 4" (102 mm) diameter for thin wall installations.
Work Area Dimensions (Shower Only):
- 30" (76 cm) diameter clearance around the handle.
- 48" (122 cm) diameter clearance for the shower arm and showerhead.
- 1¼" (32 mm) diameter hole for the handle.
Wall Thickness for Plasterguard:
- Thin Wall Installation: 1⅜" (35 mm) maximum.
- Thick Wall Installation: 1⅝" - 2¾" (41 mm - 70 mm) maximum.
Valve Rough-in Depth: An optional Extension Kit 970-083 is available, offering an additional ⅞" if the valve is roughed in too deep.
Tub Spout Connection Options:
- Option 1: Threaded Iron Pipe connection, with a rough-in distance of 4" - 4⅛" (101.6 mm - 104.8 mm) from the finished wall.
- Option 2: Copper Pipe connection, with a rough-in distance of 1½" - 2¼" (38 mm - 57 mm) from the finished wall.
Showerhead Flow Restrictor: The showerhead includes a flow restrictor, which must be inside the showerhead for proper operation and water efficiency.

Usage Features:

Water Control: The handle allows for turning the water on/off and adjusting the temperature.
Shower Activation: To turn on the shower, the handle needs to be pulled up.
Temperature Adjustment: The handle rotates to adjust between cold and hot water. The "off" position for the handle is vertical.
Showerhead Functions: The showerhead offers multiple spray settings, which can be selected by rotating the showerhead face:
- Massage: A concentrated, pulsating spray.
- Full + Massage Combo: A combination of full spray and massage.
- Full Spray: A wide, consistent spray.
Tub Spout: Provides water flow for filling a bathtub. The design ensures the screw hole on the tub spout faces down for proper installation.

Maintenance Features:

Initial Flush: After installation, it is recommended to allow full hot and full cold water to run for at least 15 seconds each to flush the lines. This helps clear any debris from the plumbing system before regular use.
Leak Check: After turning on the water supply, it is crucial to check for any leaks around all connections.
Cleaning: The guide mentions using a "Cloth" (Paño de limpieza / Chiffon) as an additional helpful tool, implying that regular cleaning of the trim surfaces is expected to maintain appearance. Specific cleaning instructions are not detailed in this quick guide but are generally recommended for plumbing fixtures.
Troubleshooting/Support: The guide provides contact information (1-800-PFAUCET, pfisterfaucets.com/support) for personal assistance, product specifications, and "how-to" questions, indicating ongoing support for maintenance and troubleshooting. Installation videos are also available online.

Installation Process Overview:

The installation process is broken down into several steps:

Turn Off Water Supply: Crucial first step to prevent flooding. Involves locating and shutting off main water supply valves, typically near the water meter.
Prepare for Installation: Involves inspecting the work area to ensure adequate clearance and proper wall thickness for the plasterguard.
Install Retainer and Stem: Involves securing the retainer and stem components to the valve body.
Install Flange and Handle: Attaching the decorative flange and the control handle. The handle must be hand-tightened and positioned in the vertical "off" position.
Connect Shower Arm & Spout: Installing the shower arm, showerhead, and tub spout. This step includes options for threaded iron pipe or copper pipe connections for the tub spout.
Turn On Water & Flush: Re-establishing water supply, checking for leaks, and flushing the system to ensure proper operation and clear any debris.

Safety Information:

The guide includes a prominent "WARNING/ADVERTENCIA/AVERTISSEMENT" section emphasizing the importance of reading all instructions, wearing safety goggles, and ensuring installation complies with all codes. It also advises calling a professional if uncertain about any installation step. The warning specifically highlights the product's exclusive compatibility with the Pfister™ OX8 Series Pressure Balancing Valve to prevent improper installation and potential issues.