No sound /power
–
Volume not adjusted
• Adjust the VOLUME
–
Mains lead not securely connected
• Connect the AC mains lead properly
–
Batteries exhausted/ incorrectly inserted
• Insert (fresh) batteries correctly
–
Headphones connected to the set
• Disconnect headphones
--
CD contains non-audio files
•Press SEARCH
or §
§
. once or more to skip to a
CD audio track, instead of the data file
Severe radio hum or noise
–
Electrical interference: set too close to TV, VCR or
computer
•Move the set to increase the distance
Poor radio reception
–
Weak radio signal
• FM: Adjust the FM telescopic aerial
noPr indication
–
During programming radio preset stations, you have
keyed in a preset number that exceeds the maximum
preset number i.e. 40
• Key in a preset number from 1-40
nOdISc indication
–
CD badly scratched or dirty
•
Replace/ clean CD, see Maintenance
–
Laser lens steamed up
•Wait until lens has cleared
nFdISc indication
–
CD-R(W) is blank/ not finalized
•
Use a finalized CD-R(W)
Sound skips during MP3 playback
--
MP3 file made at compression level exceeding
320kbps
• Use a lower compression level to record CD tracks
into MP3 format
Cannot find desired MP3 title
--
Wrong file extension used and/ or file name with
unsuitable text characters used
•Make sure the file names are typed in English text
characters an that the MP3 files end with .MP3
The CD skips tracks
–
CD damaged or dirty
• Replace or clean CD
–
SHUFFLE or PROGRAM is active
• Switch off SHUFFLE / PROGRAM
Remote control does not function properly
–
Batteries exhausted/ incorrectly inserted
• Insert (fresh) batteries correctly
–
Distance/ angle between the set too large
• Reduce the distance/ angle
Programming track numbers
In the stop position, select and store your CD tracks in
the desired sequence. Up to 20 tracks can be stored in
the memory.
1.
Press SEARCH
or §
§
on the set to select your
desired track number.
MP3-CD mode only:
First press ALBUM, PRESET
+
or
-
once or more to
find your album.
2.
Press PROG.
™ Display:
PROGRAM
and Prog.(See
6
)
™ If you attempt to program without first
selecting a track number, nOSEL is shown.
3.
Repeat steps 1-2 to select and store all desired
tracks.
™ Display: FuLL if you try to program more
than 20 tracks.
Reviewing the program
In the stop position, press and hold PROG until the
display shows all your stored track numbers in
sequence.
Erasing a program
You can erase the program by:
•pressing
9
twice
™ CLr is displayed briefly and
PROG
disappears.
•You select TUNER /POWER OFF.
SAFETY & MAINTENANCE INFORMATION
(See
8
)
• Don’t expose the set, batteries or CDs to humidity,
rain, sand or excessive heat.
•Clean the set with a dry cloth. Don't use any
cleaning agents containing alcohol, ammonia,
benzene or abrasives as these may harm the set.
•Place the set on a hard and flat surface so that the
system does not tilt. Make sure there is good
ventilation to prevent the set overheating.
•The mechanical parts of the set contain self-
lubricating bearings and must not be oiled or
lubricated.
CD player and CD handling
•If the CD player cannot read CDs correctly, use a
cleaning CD to clean the lens before taking the set
to repair.
• The lens of the CD player should never be touched!
• Sudden changes in the surrounding temperature
can cause condensation on the lens of your CD
player. Playing a CD is then not possible. Do not
attempt to clean the lens but leave the set in a
warm environment until the moisture evaporates.
•Always close the CD door to avoid dust on the lens.
•To clean the CD, wipe in a straight line from the
centre towards the edge using a soft, lint-free
cloth. Do not use cleaning agents as they may
damage the disc.
• Never write on a CD or attach any stickers to it.
MP3-CD PLAYER SAFETY AND MAINTENANCE TROUBLESHOOTING
WARNING:
Do not open the set as there is a risk of electric shock. Under no
circumstances should you try to repair the set yourself, as this will
invalidate the guarantee.
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
Environmental information
We have done our best to reduce the packaging and make it easy to separate into 3 materials:
cardboard, expandable polystyrene, polyethylene.
Your set consists of materials which can be recycled if disassembled by a specialized company.
Please observe the local regulations regarding the disposal of packaging, exhausted
batteries and old equipment.
To Next Page
Loading...
