Philips AZ1018 - Important Safety Instructions

INSTRUCTIONS FOR USE
3-2
PCS 107 139
‹ If BATT LOW lights up, battery power
is running low.The BATT LOW indicator eventually goes out if the batteries are too weak.
Batteries contain chemical substances, so they should be disposed of properly. Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst.Therefore:
• Do not mix battery types: e.g. alkaline with
carbon zinc. Only use batteries of the same type for the set.
• When inserting new batteries, do not try to
mix old batteries with the new ones.
• Remove the batteries if the set is not to be
used for a long time. Using AC Power
1 Check if the mains voltage, as shown on
the type plate located on the bottom of the set, corresponds to your local mains supply. If it does not, consult your dealer or service centre.
2 Connect the mains lead to the AC MAINS
inlet and the wall socket.The power supply is now connected and ready for use.
3 If your set is equipped with a voltage
selector, adjust the selector to match the local mains. Disconnect the mains lead if this selector has to be reset.
4 To switch off completely, unplug the mains
lead from the wall socket.
• Unplug the mains lead from the wall socket
to protect your set during heavy thunderstorms. The type plate is located on the bottom of the set. Switching power on/off: Save energy Whether you are using mains or battery supply, to avoid unnecessary energy consumption always adjust the POWER slider to TAPE/OFF and check if the cassette keys are released. General operation
1 To select your sound source adjust the
POWER slider to CD, RADIO or TAPE/OFF.
2 Adjust the sound with the VOLUME and
DBB (Dynamic Bass Boost) controls.
3 To switch off the set, adjust the POWER
slider to TAPE/OFF position and check the cassette keys are released. Note:When the set is switched off the tuner presets will be retained in the set’s memory.
Power Supply
∑
TAP
OFF
MW
FM
CD
P
L
A
Y
S
T
O
P
•
O
P
E
N
P
A
U
S
E
S
E
A
R
C
H
R
E
C
O
R
D
N
E
P
O
O
T
T
F
I
L
POWER
VOLUME
CD MODE
PROGRAM
PRESET
SEARCH
PLA
Y
-
PAUSE
STOP
FM•MW
A
Z
1
0
1
8
C
D
R
A
D
I
O
C
A
S
S
E
T
T
E
R
E
C
O
R
D
E
R
BATT
LOW
Radio reception
1 Adjust the POWER slider to RADIO.
‹ Display: shows tu briefly.The radio
frequency is then shown.
2 Press FM•MW once or more to select the
desired waveband. ‹ Display: shows your waveband
3 Press and hold down SEARCH ∞ or §
briefly to tune to a radio station. Release when the frequency in the display starts to change. ‹ The radio automatically tunes to a radio
station of sufficient reception. Display shows Srch during automatic tuning.
• To tune to a weak station, press SEARCH
∞ or § briefly and repeatedly until you have found optimal reception. To improve reception – For FM, pull out the telescopic aerial. Incline and turn the aerial. Reduce its length if the signal is too strong (very close to a transmitter). – For MW (AM) the set is provided with a built-in aerial so the telescopic aerial is not needed. Direct the aerial by turning the whole set.
4 To switch off the radio, adjust the POWER
slider to TAPE/OFF position and check the cassette keys are released.
Programming radio stations You can store up to a total of 30 radio stations in the memory.
1 Tune to your desired station (see Radio
Reception).
2 Press CD MODE/ PROGRAM to
activate programming. ‹ Display: PROGRAM flashes.
3 Press PRESET 3 or 4 once or more to
allocate a number from 1 to 30 to this station.
4 Press CD MODE/ PROGRAM again to
confirm the setting. ‹ Display: PROGRAM disappears, the preset
number and the frequency of the preset station are shown.
5 Repeat the above four steps to store other
stations.
• You can erase a preset station by storing
another frequency in its place. Tuning to preset stations Press PRESET 3 or 4 until the desired preset station is shown.
Radio
∑
D
I
G
I
T
A
L
T
U
N
E
R
B
A
S
S
R
E
F
L
E
X
S
P
E
A
K
E
R
S
Y
S
T
E
M
TAP
OFF
MW
FM
CD
P
L
A
Y
S
T
O
P
•
O
P
E
N
P
A
U
S
E
S
E
A
R
C
H
R
E
C
O
R
D
N
E
P
O
O
T
T
F
I
L
POWER
VOLUME
CD MODE
PROGRAM
PRESET
SEARCH
PLA
Y
-
PAUSE
STOP
FM•MW
A
Z
1
0
1
8
C
D
R
A
D
I
O
C
A
S
S
E
T
T
E
R
E
C
O
R
D
E
R
BATT
LOW
TAP
OFF
MW
FM
CD
P
L
A
Y
S
T
O
P
•
O
P
E
N
P
A
U
S
E
S
E
A
R
C
H
R
E
C
O
R
D
N
E
P
O
O
T
T
F
I
L
POWER
VOLUME
CD MODE
PROGRAM
PRESET
SEARCH
PLA
Y
-
PAUSE
STOP
FM•MW
A
Z
1
0
1
8
C
D
R
A
D
I
O
C
A
S
S
E
T
T
E
R
E
C
O
R
D
E
R
BATT
LOW