Philips AZ1018 - Using AC Power; Switching Power On;Off; General Operation

PCS 107 142
3-5
INSTRUCTIONS FOR USE
Synchro Start CD recording
1 Select CD source. 2 Insert a CD and if desired, programme
track numbers.
3 Press STOP•OPEN 9/ to open the
cassette door. Insert a blank tape.
4 Close the cassette door. 5 Press RECORD 0 to start recording. • Playing of the CD programme starts
automatically from the beginning of the programme. It is not necessary to start the CD player separately.
6 For brief interruptions press PAUSE ;.To
resume recording, press PAUSE ; again.
7 To stop recording, press STOP•OPEN 9/.
Selecting and recording a particular passage
• During CD playback, press and hold down
the SEARCH buttons ∞ or § on the set to find your passage.
• Press PLAY•PAUSE 2; to put the CD
player on pause at the selected passage. ‹ Recording will begin from this exact
point in the track when you press RECORD 0.
Recording from the Radio
1 Select RADIO source and your waveband. 2 Tune to the desired radio station (see
Radio reception).
3 Press STOP•OPEN 9/ to open the
cassette door. Insert a blank tape.
4 Close the cassette door. 5 Press RECORD 0 to start recording. 6 For brief interruptions, press PAUSE ;.To
resume recording, press PAUSE ; again.
7 To stop recording,
press STOP•OPEN 9/. Precautions & General Maintenance
• Place the set on a hard and flat surface so
that the system does not tilt.
• Do not expose the set, batteries, CDs or
cassettes to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight.
• Do not cover the set. Adequate ventilation
with a minimum gap of 6 inches between the ventilation holes and surrounding surfaces is necessary to prevent heat build- up.
• The mechanical parts of the set contain
self-lubricating bearings and must not be oiled or lubricated.
• To clean the set, use a soft, slightly
dampened chamois leather. Do not use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing.
Recording Maintenance
TAP
OFF
MW
FM
CD
P
L
A
Y
S
T
O
P
•
O
P
E
N
P
A
U
S
E
S
E
A
R
C
H
R
E
C
O
R
D
POWER
VOLUME
CD MODE
PROGRAM
PRESET
SEARCH
PLA
Y
-
PAUSE
STOP
FM•MW
A
Z
1
0
1
8
C
D
R
A
D
I
O
C
A
S
S
E
T
T
E
R
E
C
O
R
D
E
R
N
E
P
O
O
T
T
F
I
L
BATT
LOW
If a fault occurs, first check the points listed below before taking the set for repair. Do not open the set as there is a risk of electric shock. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. WARNING: Under no circumstances should you try to repair the set yourself, as this will invalidate the guarantee.
Troubleshooting
Problem Solution No sound – Adjust the VOLUME No power – Mains lead not securely connected.
Connect AC mains lead properly – Batteries exhausted /incorrectly inserted.
Insert (fresh) batteries correctly
Display does not function – Electrostatic discharge properly/ No reaction to Switch off and unplug the set. operation of any of the Reconnect after a few seconds. controls no d1SC, Cd Err or – No CD inserted, insert a CD nF d1SC indication – CD badly scratched/ dirty.
Replace/ clean CD (see maintenance) – CD-R(W) is blank or the disc is not finalized. Use a finalized CD-R(W) – Laser lens steamed up.Wait until lens has acclimatized
Laser lens steamed up – Wait until lens has cleared
– Wait until lens has acclimatized
CD playback does not work – CD badly scratched/ dirty.
Replace/ clean CD (see maintenance)
The CD skips tracks – CD damaged or dirty. Replace or clean CD.
– Programme is active. Quit programme mode
Poor cassette sound quality – Dust and dirt on the heads, etc.
Clean deck parts, see maintenance. – Use of incompatible cassette types (METAL or CHROME). Only use NORMAL (IEC I) for recording
Recording does not work – Cassette tab(s) may be broken.
Apply a piece of adhesive tape over the missing tab space.