Philips BT114 - User Manual

Questions and Answers

M
Maurice SandersAug 8, 2025
What to do if my Philips BT114 Portable Speakers won't turn on?
- C
  Crystal MoranAug 9, 2025
  If your Philips Portable Speakers have no power, charge the unit using a USB charging cable.
C
Curtis WolfeAug 14, 2025
What to do if my Philips Portable Speakers audio quality is poor after Bluetooth connection?
- C
  Caitlin MayAug 14, 2025
  If the audio quality is poor after connecting your Philips Portable Speakers with a Bluetooth enabled device, try moving the device closer to the speaker or removing any obstacles between them.
D
dodsonalexandraAug 19, 2025
Why can't I connect my device to my Philips BT114?
- T
  Thomas RichardsonAug 19, 2025
  If you can't connect your device to your Philips Portable Speakers, it might already be connected to another Bluetooth enabled device. Disconnect that device and then try again.
S
solomoncatherineAug 25, 2025
What to do if there is no sound or distorted sound from my Philips BT114 Portable Speakers?
- S
  Steven MartinezAug 25, 2025
  If you experience no sound or distorted sound from your Philips Portable Speakers, adjust the volume or select the correct source to choose the equipment that you want to hear through the system.
C
Colton ThomasAug 28, 2025
What to do if my Philips BT114 Portable Speakers are not responding?
- M
  Mary WellsAug 29, 2025
  If your Philips Portable Speakers are not responding, try restarting the speaker.
T
Tracy HigginsSep 3, 2025
How to stop low hum or buzz sound from Philips BT114 Portable Speakers?
- E
  Elijah BaileySep 3, 2025
  To eliminate a low hum or buzz sound from your Philips Portable Speakers, place the product as far away as possible from electrical devices that may be causing interference.

This document is a user manual for the Philips BT114 Portable Speaker.

Function Description

The Philips BT114 is a portable speaker designed for wireless audio playback via Bluetooth, as well as wired connections and other media sources. It functions as a versatile audio device, allowing users to play music from various sources, make hands-free phone calls, and listen to FM radio.

Important Technical Specifications

Amplifier:

Rated output power: 10W RMS
Signal to Noise Ratio: >50dB
Audio input: 600MV
Frequency Response: 70Hz~20KHz

Speaker:

Speaker Impedance: 4 ohm
Speaker Driver: 1.75 inch/4.5cm
Sensitivity: 80 dBm

Bluetooth:

Bluetooth version: V4.0
Bluetooth profile: V2.1+EDR
Bluetooth frequency: 2.4GHz~2.48GHz
Bluetooth range: Up to 10M (freespace)

General Introduction:

Power supply: 5V 1A
Built-in Battery: Li-polymer battery
Dimension main unit (LxWxH): 56x75x178.5mm
Weight: 369g
Connectivity: FM, USB, Audio in, Bluetooth

Usage Features

Power and Source Selection:

Power On/Off: Long press the "power" button.
Source Selection: Short press the "power" button to cycle through Bluetooth, Audio in, FM, and USB modes. Audio in and FM modes are available only when the stereo cable is connected. USB mode is available only when a USB device is inserted.

Bluetooth Mode:

Pairing: Long press the "power" button to turn on the unit; it will enter Bluetooth mode with a quickly flashing blue LED. Search for "PHILIPS BT114" on your Bluetooth device. A "Beep" sound indicates entering pairing mode, and a double "Beep" confirms successful pairing. The blue light will stop flashing. The default password, if required, is "0000".
Automatic Reconnection: After successful pairing, the device will automatically connect to the speaker next time.
Disconnecting: Long press the "play/pause" button for 3 seconds to disconnect the current device and enter pairing mode.
LED Indicator: Blue LED for Bluetooth mode.

Audio In Mode:

Connection: Connect a 3.5mm stereo cable from the external audio device's headphone socket to the speaker's Audio In socket.
Activation: Inserting the stereo cable automatically activates Audio In mode. The speaker cannot enter Audio In mode without the cable.
LED Indicator: Green LED for Audio In mode.

FM Mode:

Activation: Connect an audio stereo cable (acting as an antenna) and short press the "power" button until the speaker enters FM mode. The LED will flash blue & green alternatively.
Channel Search & Save: Long press the "play/pause" button to search and save all FM channels from 87.5 to 108Hz.
Channel Selection: Use the "-" or "+" buttons (short press) to select desired channels.
Requirement: FM mode requires the audio cable to be connected.
LED Indicator: Blue and green LEDs alternate for FM mode.

USB Mode:

Activation: Insert a USB device and short press the "power" button to select USB mode. The LED will change to light blue. The speaker cannot convert to USB mode if the USB is not fully inserted.
LED Indicator: Light blue LED for USB mode.

Playback Controls (common across modes where applicable):

Play/Pause: Short press the "play/pause" button.
Previous Song/Track: Short press the "-" button.
Next Song/Track: Short press the "+" button.

Volume Control:

Volume Decrease: Long press the "-" button.
Volume Increase: Long press the "+" button. A sound will be made when the volume reaches its higher limit.

Hands-free Phone Call Function:

Incoming Call: Blue light flashes, and the speaker emits a 'Beep' sound.
Answer Call: Short press the "play/pause" button.
End Call/Reject Call: Short press the "play/pause" button.
Adjust Volume: Use the "-" or "+" buttons to decrease or increase call volume.
Disconnect Bluetooth during call: Long press the "play/pause" button.

Charging:

Connection: Connect the micro USB charging cable to the speaker's DC In socket and to a computer's USB socket or a standard 5V 1A charger.
Charging Time: 3-4 hours.
Over-charging Protection: The speaker has an internal over-charging protective circuit.
LED Indicator: Orange LED for charging.
Low Power Warning: When the battery is low, the speaker will emit a "Beep" sound, and the volume will decrease to maintain playback quality. The speaker will shut down if there is no power.

Maintenance Features

General Care:

Placement: Place the speaker on a flat surface.
Ventilation: Ensure adequate ventilation by allowing at least 10cm (4 inches) of free space around the apparatus to prevent heat buildup.
Cleaning: Use a soft cloth slightly moistened to clean the cabinet. Avoid solutions containing alcohol, spirits, ammonia, or abrasives.
Environmental Conditions: Avoid high temperatures, moisture, water, and dust. Do not expose the apparatus to dripping or splashing liquids. Do not place liquid-filled objects or lighted candles on the speaker. Do not install near heat sources.
Indoor Use Only: The device is intended for indoor use.

Battery Care:

Initial Charge: Fully charge the built-in battery before first use.
Charging Socket: The micro USB socket is for charging only.
Battery Life: Rechargeable batteries have a limited number of charge cycles; life varies by use and settings.
Long-term Storage: If not using the speaker for a long time, ensure it is fully charged once every month to protect the battery.

Troubleshooting:

No Power: Charge the unit using the USB charging cable.
No Sound/Distorted Sound: Adjust volume or select the correct source.
Low Hum/Buzz Sound: Place the product away from other electrical devices causing interference.
No Response: Restart the speaker.
Poor Audio Quality (Bluetooth): Move the device closer to the speaker or remove obstacles.
Cannot Connect (Bluetooth): Disconnect any other connected Bluetooth devices and try again.
Warranty: Do not attempt to repair the system yourself, as this will invalidate the warranty and poses a risk of electric shock. Consult your dealer or Philips APSC for assistance.