View Clock
You can view the clock (if it is set) if the system
is in Standby mode or when any sound source is
selected (CD, TUNER, etc.). The clock will be
displayed for about seven seconds.
¶ Press CLOCK•TIMER briefly (on the system
only).
➜ “10:38
PM
or 22:38” (the current time)
will be displayed depending on whether you
have selected 12- or 24-hour mode.
➜ “--:--” will be displayed if the clock is not
set.
Clock Setting
The clock can be set in either 12- or 24-hour
mode, e.g. “12:00
AM
“ or “00:00“. Before
setting the clock, you must be in the View Clock
mode.
1
Press CLOCK•TIMER to select clock mode.
2
Press PROGRAM to select 12- and 24- hour
mode.
➜ If 12-hour mode is selected, “12:00“ starts
flashing and the
AM
lights up.
➜ If 24-hour mode is selected, “00:00” starts
flashing.
3
Set the hour with à or á on the system.
4
Set the minute with í or ëon the system.
5
Press CLOCK•TIMER again to store the
setting.
➜ The clock starts.
¶ To exit without storing the setting, press Çon
the system.
Notes:
– During clock setting, if no button is pressed
within 90 seconds, the system will exit clock setting
mode automatically.
– When a power interruption occurs, the clock
setting is erased.
Timer Setting
¶ The system can switch on to CD or TUNER
mode automatically at a preset time. It can serve
as an alarm to wake you up.
¶ Before setting the timer, make sure the clock is
set correctly.
¶ The timer will always be switched on once it is
set.
¶ The volume of the timer will increase
from the minimum level to the most
recently selected volume level.
1
Press and hold CLOCK•TIMER for more than
2 seconds to select timer mode.
➜ “TU__XX:XX” or “CD__XX:XX" starts
flashing. "XX:XX" is “12:00
AM
“ or “00:00” or
the last timer setting, depending on whether 12-
or 24-hour mode has been selected.
➜ The
TIMER
starts flashing.
2
Press CD or TUNER to select the desired
source.
➜ “TU__XX:XX” indicates the Tuner mode is
selected.
➜ “CD__XX:XX" indicated the CD mode is
selected.
¶ Before selecting CD, make sure a disc is loaded
in the CD changer tray.
24
English
Clock/Timer
3
Press à or á on the system to set the hour
for the timer to start.
4
Press í or ë on the system to set the minute
for the timer to start.
5
Press CLOCK•TIMER to store the start time.
➜ The timer is now set.
➜ The
TIMER
remains on the display.
¶ At the preset time, the timer will be activated.
➜ The selected source will be played.
Notes:
– During timer setting, if no button is pressed
within 90 seconds, the system will exit timer setting
mode automatically.
– If the source selected is TUNER, the last tuned
frequency will be switched on.
– If the source selected is CD, playback will begin
with the first track of the selected disc or
programme. If the disc trays are empty, the TUNER
will be selected instead.
– The timer will not activate if a recording is in
progress.
To switch off the TIMER
1
Press and hold CLOCK•TIMER for more than
2 seconds.
2
Press Ç on the system to cancel the timer.
➜ The timer is now switched off.
➜ The display will show "OFF" and the
TIMER
disappears.
To start the TIMER again (for the same
preset time and source)
1
Press and hold CLOCK•TIMER for more than
2 seconds.
2
Press CLOCK•TIMER again to store the start
time.
➜ The timer is now on.
➜ The
TIMER
appears on the display.
Sleep Timer
(only on remote control)
This feature allows you to select a length of time
after which the system will switch to the standby
mode automatically.
1
Press SLEEP on the remote control repeatedly
to select a period of time.
➜ The selections are as follows (time in
minutes): 15
™™
™™
™ 30
™™
™™
™ 45
™™
™™
™ 60
™™
™™
™ OFF
™™
™™
™
15 …
➜ "SLEEP XX" or "OFF" will be displayed. "XX"
is the time in minutes.
2
When you reach the desired length of time, stop
pressing the SLEEP button.
➜ The
SLEEP
display lights up.
➜ The Sleep Timer is now set. Before the
system switches to standby mode, a countdown
of 10 seconds will be displayed.
"SLEEP 10"
™™
™™
™ "SLEEP 9"....
™™
™™
™ "SLEEP 1"
™™
™™
™ "SLEEP"
While SLEEP mode is activated
¶ Press SLEEP once to view the remaining length
of time.
¶ Press SLEEP twice to change the pre-selected
period of time.
➜ The display will show the remaining time
followed by the sequence of sleep timer options.
To switch off the Sleep Timer
¶ Press SLEEP repeatedly until "OFF" is displayed,
or press the STANDBY-ON button.
To Next Page
Loading...
