9
English
Preparation
Controls
(illustrations on page 3)
D
Connecting other equipment to your
player
You can connect the audio left and right OUT
terminals of a TV, VCR, Laser Disc player, DVD
player or CD Recorder to the AUX IN terminals
at the rear of the system.
E
AC Power Supply
After all other connections have been made,
connect the AC power cord to the system and
to the wall outlet.
Inserting batteries into the
Remote Control
¶ Insert the batteries (Type R06 or AA) into the
remote control as shown in the battery
compartment.
¶ To avoid damage from possible battery leakage,
remove dead batteries or batteries that will not
be used for a long time.
Batteries contain chemical substances, so
they should be disposed off properly.
Controls on the player and
remote control
1
STANDBY-ON
yy
yy
y
– switches the system to standby/on.
2
PROGRAM
for CD ................. to programme disc tracks.
for TUNER ........ to programme preset radio
stations.
for CLOCK ....... to select 12 or 24 hour in clock
setting mode
.
3
DSC (DIGITAL SOUND CONTROL)
– to select the desired sound effect :
OPTIMAL, JAZZ, ROCK or TECHNO.
4
DISPLAY SCREEN
– to view the current setting of the system.
5
CD CHANGER TRAY
6
DISC CHANGE
– to change disc(s).
7
OPEN•CLOSE
– to open or close the CD changer tray.
8
DISC 1 / DISC 2 / DISC 3 (DISC DIRECT
PLAY)
– to select a disc tray for playback.
9
SOURCE – to select the following:
CD / (CD 1•2•3)
– to select CD mode. When disc playback is
stopped, press to select disc tray 1, 2 or 3.
TUNER / (BAND)
– to select Tuner mode. When in tuner mode,
press to select the waveband: FM, MW or LW.
TA PE / (TAPE 1• 2)
– to select Tape mode.
AUX (VIDEO)
– to select sound from an external source (e.g. TV,
VCR, Laser Disc player, DVD player or CD
Recorder).
0
MODE SELECTION
SEARCH àá (TUNING àá )
for CD ................. to search backward/forward.
for TUNER ......... to tune to a lower or higher radio
frequency.
for CLOCK ....... to set the hour (on the system
only)
.
STOP•CLEAR Ç
for CD ................. to stop disc playback or to clear
a programme.
for TUNER ........ to stop programming (on the
system only).
for DEMO ......... to start or stop demonstration
mode (on the system only).
for CLOCK ....... to exit clock setting or cancel
timer (on the system only).
for PLUG & PLAY
................................. to exit plug & play mode and
return to standby mode (on the
system only).
PLAY É / PAUSE Å
for CD ................. to start or interrupt playback.
for PLUG & PLAY
................................. to initiate and star t plug & play
from standby/demo mode (on
the system only).
PREV í / NEXT ë(PRESET 4 3 )
for CD ................. to skip to the beginning of the
current, previous, or next track.
for TUNER ........ to select a preset station in
memory.
for CLOCK ....... to set the minute (on the system
only)
.
! MASTER VOLUME 4 3
– to increase or decrease the volume.
@ n
– to connect headphones.
# DBB (DYNAMIC BASS BOOST)
– to switch on bass boost to enhance bass
response or to switch off bass boost.
$ CLOCK•TIMER
– to view the clock, set the clock or set the timer.
%
TAPE DECK 2
^
TAPE DECK 2 OPERATION
PLAYÉ ........... to start playback.
à .......................... to rewind the tape.
á .......................... to fast forward the tape.
STOP•OPEN…to stop playback or to open
the tape door.
PAU S E .............. to interrupt playback.
& TAPE DECK 1 OPERATION
RECORD ........ to start recording.
PLAYÉ ........... to start playback.
à .......................... to rewind the tape.
á .......................... to fast forward the tape.
STOP•OPEN…to stop playback/recording or
to open the tape door.
PAU S E .............. to interrupt playback or
recording.
* TAPE DECK 1
( DIM
– to select different brightness for the display
screen : DIM 1, DIM 2, DIM 3 or DIM OFF.
) REPEAT
– to repeat a disc track, a disc, or all available discs.
¡ MUTE
– to switch off the sound temporarily.
™ SHUFFLE
– to play all the available discs and their tracks in
random order.
£ SLEEP
– to switch the system to standby mode at a
selected time.
≤ B
– to switch the system to standby mode.
Notes for remote control:
– First select the source you wish to control
by pressing one of the source select keys on
the remote control (e.g. CD , TUNER, etc.).
– Then select the desired function (É,
í,
ë, etc.).
To Next Page
Loading...
