17
English
Tuner
Note:
–For 'PLUG & PLAY' feature, please refer to page
11.
Tuning to radio stations
1
Press TUNER (BAND) to select TUNER mode.
➜ “TUNER” will be displayed.
A few seconds later, the current radio
frequency will be displayed.
2
Press TUNER (BAND) again to select the
desired waveband : FM or MW.
3
Press à or á for more than one second, then
release.
➜ The display will show “SEARCH” until a radio
station with sufficient signal strength is found.
¶ Repeat this procedure until the desired station is
reached.
¶ To tune to a weak station, briefly press à or
á repeatedly until the display shows the
desired frequency and/or when the best
reception has been obtained.
Storing Preset Stations
You can store up to 40 radio stations in the
memory. When a preset radio station is selected,
the preset number appears next to the
frequency on the display.
Automatic programming
1
Press TUNER (BAND).
2
Press PROGRAM for more than one second.
➜ The PROG flag starts flashing and “AUTO” will
be displayed.
➜ The system will search for every available
station in the FM waveband first, then search the
MW waveband.
➜ All available stations will be stored
automatically. The frequency and preset number
will be displayed briefly.
➜ The system will stop searching when all the
available radio stations are stored or when the
memory for 40 preset radio stations is used.
➜ The system will remain tuned to the last
stored preset radio station.
18
English
Tuner
Notes:
–You can cancel the automatic programming by
pressing PROGRAM or
Ç
(on the system only).
– If you want to reserve a section of preset
numbers, for example preset numbers 1 to 9,
select preset 10 before starting automatic
programming, only the preset numbers 10 to 40
will be programmed.
Manual programming
1
Press TUNER (BAND).
2
Press TUNER (BAND) again to select the
desired waveband : FM or MW.
3
Press PROGRAM for less than one second.
➜ The PROG flag starts flashing.
➜ The next available preset number will be
displayed for selection.
4
Press à or á to tune to the desired frequency.
¶ If you wish to store the radio station to another
preset number, press 4 or 3 to select the
desired preset number.
5
Press PROGRAM again.
➜ The PROG flag disappears and the radio
station will be stored.
¶ Repeat steps 3 – 5 to store other preset radio
stations.
Notes:
– When 40 radio stations are stored and you
attempt to store another radio station, the display
will show "FULL”. If you want to change an
existing preset number, repeat steps 3 – 5.
–You can cancel manual programming by
pressing
Ç
(on the system only).
– During programming, if no button is pressed
within 20 seconds, the system will exit programme
mode automatically.
Tuning to Preset Radio Stations
¶ Press 4 or 3 to select the desired preset
number.
➜ The preset number, radio frequency, and
waveband appear on the display.
Changing the MW tuning grid
(not
available for version /30)
The frequency step can be changed if necessary.
In North and South America, the frequency step
between adjacent channels in the MW band is
10 kHz. In other parts of the world, it is 9 kHz.
The frequency step preset in the factory is
9 KHz.
For MW Band
To change from 9 kHz to 10 kHz or vice
versa
Changing of tuning grid will erase all
previously stored preset stations.
1
Disconnect the system from the AC power
supply (pull out the AC power cord).
2
Press and hold TUNER and TUNING á
while reconnecting the system to the AC power
supply.
➜ Display will show “GRID 10” or “GRID 9”.
Notes:
– GRID 9 indicates that the tuning grid is in step
of 9 kHz in MW band. GRID 10 indicates that the
tuning grid is in step of 10 kHz in MW band.
– FM tuning grid will also be changed from
50 kHz to 100 kHz or vice versa.
To Next Page
Loading...
