23
English
CD Synchro Start Recording
During CD synchro start recording,
¶ Do not fast forward/rewind your tape in tape
deck 2.
1
Load a blank tape into tape deck 1 and a disc
into the disc tray.
2
Press CD.
¶ You can programme the tracks in the order you
want them to be recorded (see Programming
Tracks). If you do not, the tracks are recorded
according to the order on the selected disc.
3
Press RECORD on tape deck 1 to start
recording.
➜ The
REC
starts flashing.
4
Press STOP•OPEN on tape deck 1 to stop
recording, then press Ç to stop CD playback.
Dubbing tapes
(from tape deck 2 to tape
deck 1)
1
Load the prerecorded tape into tape deck 2 and
a blank tape into tape deck 1.
¶ Make sure both tapes have their full spool to the
left.
2
Press PAUSE on tape deck 1.
3
Press RECORD on tape deck 1.
➜ The
REC
starts flashing.
4
Press PLAYÉ on tape deck 2.
¶ Recording will start automatically.
5
Press STOP•OPEN on tape deck 1 and tape
deck 2 to stop dubbing.
Notes:
– At the end of side A, flip the tapes to side B and
repeat the procedure.
– Dubbing of tapes is only possible from tape
deck 2 to tape deck 1.
–To ensure good dubbing, use tapes of the same
length.
Recording from other sources
(only on tape deck 1)
1
Load a blank tape into tape deck 1.
2
Press CD, TUNER or AUX.
¶ Start playback of the selected source.
3
Press RECORD on tape deck 1 to start
recording.
➜ The
REC
starts flashing.
4
Press PAUSE to interrupt recording.
5
Press STOP•OPEN on tape deck 1 to stop
recording.
Note:
– During recording, it is not possible to listen to
another sound source.
Recording
View Clock
You can view the clock (if it is set) if the system
is in Standby mode or when any sound source is
selected (CD, TUNER, etc.). The clock will be
displayed for about 7 seconds.
¶ Press CLOCK•TIMER briefly (on the system
only).
➜ “10:38
PM
or 22:38” (the current time)
will be displayed depending on whether you
have selected 12- or 24-hour mode.
➜ “--:--” will be displayed if the clock is not
set.
Clock Setting
The clock can be set in either 12- or 24-hour
mode, e.g. “12:00
AM
“ or “00:00“. Before
setting the clock, you must be in the View Clock
mode.
1
Press CLOCK•TIMER to select clock mode.
2
Press PROGRAM to select 12- and 24- hour
mode.
➜ If 12-hour mode is selected, “12:00“ starts
flashing and the
AM
lights up.
➜ If 24-hour mode is selected, “00:00” starts
flashing.
3
Set the hour with à or á on the system.
4
Set the minute with í or ëon the system.
5
Press CLOCK•TIMER again to store the
setting.
➜ The clock starts.
¶ To exit without storing the setting, press Çon
the system.
Notes:
– During clock setting, if no button is pressed
within 90 seconds, the system will exit clock setting
mode automatically.
– When a power interruption occurs, the clock
setting is erased.
Timer Setting
¶ The system can switch on to CD or TUNER
mode automatically at a preset time. It can serve
as an alarm to wake you up.
¶ Before setting the timer, make sure the clock is
set correctly.
¶ The timer will always be switched on once it is
set.
¶ The volume of the timer will increase
from the minimum level to the most
recently selected volume level.
1
Press and hold CLOCK•TIMER for more than
2 seconds to select timer mode.
➜ “12:00
AM
” or “00:00" or the last timer
setting starts flashing depending on whether you
have selected 12- or 24-hour mode.
➜ The
TIMER
starts flashing.
➜ The selected source is lit while other available
sources are flashing.
2
Press CD or TUNER to select the desired
source.
To Next Page
Loading...
