23
English
3139 116 19541
CLOCK TIMER
View Clock
You can view the clock (if it is set) if the
system is in Standby mode or when any
sound source is selected (CD, TUNER, etc.).
The clock will be displayed for about seven
seconds.
• Press CLOCK/TIMER briefly.
™ "PM 10:38 or 22:38" (the
current time) will be displayed
depending on whether you have
selected 12- or 24-hour mode.
™ "--
::
::
:--" will be displayed if the
clock is not set.
Clock Setting
The clock can be set in either 12- or 24-
hour mode, e.g. "AM 12:00" or
"00:00". Before setting the clock, you
must be in the View Clock mode.
1 Press CLOCK/TIMER to select clock
mode.
2 Press PROG
(on the system only)
to
select 12- and 24- hour mode.
™ If 12-hour mode is selected,
"AM 12:00" starts flashing.
™ If 24-hour mode is selected,
"00:00" starts flashing.
3 Set the hour with␣ à or á on the
system.
4 Set the minute with␣ í or ë on the
system.
SHUFFLE
PROGRAM
FM
STEREO
BACK
HSD
REPEAT
REC
LW
MW
AM
T.A.
NEWS
SOUND NAVIGATION
DUB
(HSD)
REC
MINI HIFI SYSTEM
TIMER
FRONT
60Hz
500Hz
250Hz
1KHz
2KHz
4KHz
8KHz
INCREDIBLE
SURROUND
DYNAMIC BASS
BOOST
TAPECD
PROG
CLOCK/
TIMER
TUNER AUX
PRESET
▲
▲
STOP•CLEAR
SEARCH • TUNING
PLAY
PAUSE PREV NEXT
CD1 • 2 • 3
CDR/VIDEO
BAND
TAPE 1 • 2
DIGITAL
SOUND CONTROL
A. REV
STANDBY
ON
SIDE
NEWS/TA
DOLBY B
NR
RDS
MIC
MIC
LEVEL
5 Press CLOCK/TIMER again to store the
setting.
™ The clock starts.
• To exit without storing the setting, press
Ç on the system.
Notes:
– During clock setting, if no button is
pressed within 90 seconds, the system
will exit clock setting mode
automatically.
– When a power interruption occurs, the
clock setting is erased.
– To set the time with RDS clock, see
"Receiving RDS Radio Station" under
TUNER section.
Timer Setting
• The system can switch on to CD,
TUNER, or TAPE 2 mode automatically
at a preset time. It can serve as an
alarm to wake you up.
• Before setting the timer, make sure the
clock is set correctly.
• The timer will always be switched on
once it is set.
• The volume of the timer will
increase from the minimum level
until the volume level before the set
is switched to standby mode.
1 Press and hold CLOCK/TIMER for more
than
2 seconds
to select timer mode.
™ "AM 12:00" or "00:00" or the
last timer setting starts flashing
depending on whether you have
selected 12- or 24-hour mode.
™ The TIMER starts flashing.
™ The selected source is lit while other
available sources are flashing.
2 Press CD, TUNER or TAPE to select the
desired source.
• Before selecting CD or TAPE, make sure
a CD or tape is loaded in the CD tray or
tape deck 2.
3 Press␣ à or á on the system to set the
hour for the timer to start.
4 Press␣ í or ë on the system to set the
minute for the timer to start.
5 Press CLOCK/TIMER to store the start
time.
™ The timer is now set.
™ The TIMER remains on the display.
• At the preset time, the timer will be
activated.
™ The selected source will be played.
Notes:
– During timer setting, if no button is
pressed within 90 seconds, the system
will exit timer setting mode
automatically.
– If the source selected is TUNER, the last
tuned frequency will be switched on.
pg 01-26/C55-C58/34-En 2/22/00, 7:02 PM23
To Next Page
Loading...
