13
English
Notes:
– When the power is turned on, the disc tray may
open and close to initialise the system.
– If you do not complete Plug and Play installation,
Plug and Play will be reinitiated the next time you
turn on the power.
– If no stereo frequency is detected during
Plug and Play, "
CHECK ANTENNA
" will be
displayed.
– During Plug and Play, if no button is pressed
within 15 seconds, the system will exit Plug and
Play mode automatically.
Demonstration mode
The system has a demonstration mode that
shows the various features offered by the system.
To activate the demonstration
● In Standby mode, press and hold DEMO
STOP on the system until "
DEMO ONDEMO ON
DEMO ONDEMO ON
DEMO ON" is
displayed.
➜ The demonstration will begin.
To deactivate the demonstration
● Press and hold DEMO STOP on the system
until "
DEMO OFFDEMO OFF
DEMO OFFDEMO OFF
DEMO OFF" is displayed.
➜ The system will switch to Standby mode.
Note:
– Even if you remove the AC power cord and
reconnect it to the wall socket, the demonstration
will remain off until you activate it again.
Switching the system on
In Standby/Demonstration mode
● Press STANDBY ON.
➜ The system will switch to the last selected
source.
● Press 3CDC (CD 123), TUNER, TA P E,
AUX/CDR.
➜ The system will switch to the selected source.
● Press any one of the disc OPEN•CLOSE
(DISC 1 / DISC2 / DISC 3) button.
➜ The system will switch to CD mode.
In Eco Power Standby mode
● Press ECO POWER.
➜ The system will switch to last selected source.
● Press CD 123, TUNER, TAPE or AUX/CDR
on the remote control.
➜ The system will switch to the selected source.
Switching the system to Standby
mode
In Demonstration mode
● Press and hold DEMO STOP on the system.
In any other source mode (except Eco
Power Standby mode)
● Press STANDBY ON (or B on the remote
control).
➜ The clock will appear on the display when the
system is in Standby mode.
Switching the system to Eco
Power Standby mode (< 1 Watt)
● Press ECO POWER (or press and hold B on
the remote control).
➜ "
ECO PWRECO PWR
ECO PWRECO PWR
ECO PWR" will be displayed, then the
display screen will go blank.
➜ The low power ECO POWER LED will be
lighted.
Note:
– If you have not deactivated the demonstration, it
will resume five seconds after the system switches
to Eco Power Standby or Standby mode.
Power Saving Automatic Standby
As a power-saving feature, the system will
automatically switch to Standby mode if you do
not press any buttons within 30 minutes after a
disc or tape has stopped playing.
Basic Functions
14
English
Dim mode
You can select the desired brightness for the
display.
● Press DIM on the remote control repeatedly to
select DIM 1, DIM 2, DIM 3 or DIM OFF display
mode.
➜
DIM
and the corresponding mode number will
appear on the display, except for DIM OFF
mode.
DIM OFF ......... All available LEDs light up, display
screen will have full brightness,
music level bar active.
DIM 1 ...............Some LEDs light up, display
screen will have full brightness,
music level bar inactive.
DIM 2 ...............All lightings turn off, display
screen will have full brightness,
music level bar inactive.
DIM 3 ...............All lightings turn off, display
screen will be at half brightness,
music level bar inactive.
+ music level bar
Volume Control
Adjust VOL to increase (turn knob clockwise or
press VOLUME +) or decrease (turn knob anti-
clockwise or press VOLUME -) the sound level.
➜ "
-XX dB-XX dB
-XX dB-XX dB
-XX dB" will be displayed. "
XXXX
XXXX
XX" denotes
the volume level.
➜ When reached the minimum volume level,
"
VOL MUTEVOL MUTE
VOL MUTEVOL MUTE
VOL MUTE" will be displayed.
To listen through the headphones
● Connect the headphones plug
to the PHONES socket at the
front of the system.
➜ The speakers will be muted.
To switch off the volume temporarily
● Press MUTE on the remote control.
➜ Playback will continue without sound and
"
MUTEMUTE
MUTEMUTE
MUTE" will be displayed.
● To restore the volume, press MUTE again or
increase the volume level.
Interactive Sound Control
For optimal sound listening, you are only
able to select BASS/TREBLE or wOOx at a
time (for model MC-70 only).
wOOx (for model MC-70 only)
There are three wOOx settings to enhance the
bass response.
● Press wOOx on the system repeatedly to
select the next wOOx level or switch off the
wOOx effect.
OR
1
Press wOOx on the remote control to switch
ON (enhanced) or OFF (normal) the wOOx
sound effect.
2
When wOOx is switched on, press wOOx
LEVEL on the remote control repeatedly to
select the desired wOOx level : WOOX 1,
WOOX 2, WOOX 3 or WOOX OFF.
➜ If “
WOOX 1WOOX 1
WOOX 1WOOX 1
WOOX 1,
22
22
2 or
33
33
3"” is selected,
WOOX
and the corresponding level
number will appear on the display.
➜ If “
WOOX OFFWOOX OFF
WOOX OFFWOOX OFF
WOOX OFF"” is selected, the
wOOx sound effect will be switched off.
Notes:
– When switched off the wOOx effect, the last
Bass/Treble will resume automatically.
– Some discs or tapes might be recorded in high
modulation, which causes a distortion at high
volume. If this occurs, deactivate wOOx or reduce
the volume.
Basic Functions
To Next Page
Loading...
