Activating and deactivating
SLEEP
The sleep timer enab les the system to switch off
by itself after a set per iod of time . The clock time
needs to be set first before the sleep timer can
be used.
Press SLEEP on the remote
control once or more .
Displ ay sho ws SLEEP and
one of the sleep time options
in sequence: 60, 45, 30,15,
SLEEP OFF, 60... if you have selected a time .
Once SLEEP is activated, SLEEP ON scrolls
across the displ ay at repeated inter vals.
Clock/Timer
Specifications
AMPLIFIER
Output power .......................................... 2 x 5 W RM S
............................................................. 10 W + 10W MP O
Signal-to-noise ratio .......................... 65 dBA (IEC)
Frequency response ......... 40 – 20000 Hz, ± 3 dB
Input sensitivity AU X ....................... 0.5 V (max. 2 V)
Impedance loudspeaker s ......................................... 8
Impedance headphones ................. 32 – 1000
CD PLAYER
Frequency range .................................. 20 – 20000 Hz
Signal-to-noise ratio ............................................ 75 dBA
TUNER
FM wave range ................................... 87.5 – 108 MHz
MW wa ve range ................................ 531 – 1602 kHz
LW wave range ..................................... 153 – 279 kHz
Sensitivity at 75
– mono , 26 dB signal-to-noise r atio ............ 2.8 ∝V
– stereo , 46 dB signal-to-noise r atio ........ 61.4 ∝V
Selectivity ................................................................. 28 dB
Total har monic distortion ..................................... 5%
Frequency response ..... 63 – 12500 Hz (± 3 dB)
Signal-to-noise-ratio ...................................... 50 dBA
To deactivate , press SLEEP on the remote
control once or more until SLEEP OFF is
shown , or press STANDBY ON on the system
or remote control.
SLEEP OFF scrolls across the display.
TAPE DECK
Frequency response
Normal tape (type I) ... 120 – 10000 Hz (8 dB)
Signal-to-noise r atio
No rmal tape (type I) .................................... 48 dBA
Wo w and flutter ......................................... 0.4% DIN
SPEAKERS
Bass reflex system
Dimensions (w x h x d) . 156 x 231 x 190 (mm)
GENERAL INFORMATION
AC Power ..................................... 220 – 230 V / 50 Hz
Dimensions (w x h x d) ... 140 x 231 x 280(mm)
We ight (with/without speaker s) ..................................
............................................................... appro x. 5.7 / 2.7 kg
Standby power consumption .......................... < 3 W
Subject to modification
Clock/Timer
Setting the timer
The system can be used as an alarm clock,
whereb y the CD or TUNER is switched on at a
set time . The clock time needs to be set first
before the timer can be used.
Du ring setting, if no button is pressed within 90
seconds, the system will exit timer setting mode
automatically.
1 In any mode , press TIMER ON•OFF for more
than 2 seconds.
2 Tu r n VOLUME clockwise (or press SELECT
SOURCE) to select sound source .
3 Press TIMER ON•OFF to conf irm your
desired mode .
The selected source
CD
or
TUNER
TUNER
is shown. The clock digits for the hours flash.
4 Tu r n VOLUME to set the hour s: clockwise for
hour s up; anti-clockwise for hours down.
5 Press TIMER ON•OFF again.
The clock digits for the minutes flash.
6 Tu r n VOLUME to set the min utes: clockwise for
minutes up; anti-clockwise for min utes do wn .
7 Press TIMER ON•OFF to conf irm the time .
The timer is now set and activated.
Activating and deactivating
TIMER
In standb y or during playback, press
TIMER ON•OFF once .
Display sho ws TIMER if activated, and
disappears if deactivated.
Setting the clock
There are two possi ble methods for setting the
clock: manually or automatically by using RDS.
Automatic clock setting (RDS versions
only)
1 Tune to a RDS station (see Radio Reception).
2 Press CLOCK SET for more than 2 seconds.
SEARCH RDS TIME is displayed for a
maximum of 90 seconds; the time is then
displayed.
NO RDS TIME is displayed if no time signal
has been receiv ed and y ou will ha ve to set the
clock man ually.
Manual clock setting
1 In standb y, press CLOCK SET.
The clock digits f or the hours flash.
2 Tu r n VOLUME to set the hour s: clockwise for
hours up; anti-clockwise for hour s do wn .
3 Press CLOCK SET again.
The clock digits for the minutes flash.
4 Tu r n VOLUME to set the min utes: clockwise fo r
minutes up; anti-clockwise for minutes down.
5 Press CLOCK SET to conf irm the time .
Note:
– The backlight for clock display is dim in standby.
To Next Page
Loading...
