— 10 —
S
ETTING
U
P
(CONTINUED)
To reset the clock manually
You can also reset or correct the clock
manually.
1 Press VCR.
2 Press MENU.
3 Press PLAY
5
or STOP
∞
to select
“INITIAL SET UP” then press
OK/STATUS.
The Initial Set Up menu appears.
4 Press PLAY
5
or STOP
∞
to select
“SET CLOCK” then press
OK/STATUS.
5 Press PLAY
5
or STOP
∞
to set the
time, then press OK/STATUS.
• Each time you press PLAY
5
or
STOP
∞
, the set time changes by 1-
minute intervals. If you press and hold
the button, the set time changes by 30-
minute intervals.
6 Press PLAY
5
or STOP
∞
to set the
day and month, then press OK/
STATUS.
• Each time you press PLAY
5
or
STOP
∞
, the set date changes by 1-
day intervals. If you press and hold the
button, the set date changes by 15-day
intervals.
7 Press PLAY
5
or STOP
∞
to set the
year, then press OK/STATUS.
• Each time you press PLAY
5
or
STOP
∞
, the set year changes by 1-
year intervals. If you press and hold the
button, the set year changes rapidly.
8 Press MENU to exit from the menu
operations.
Note:
If a power failure occurs, clock will lose its
setting.
Menu Operations
Before operating the VCR, be
familiar with the menu operations
first because most of the features
built into the VCR can be available
only on the menus.
1 Press VCR on the remote control.
• When using the buttons on front
panel, skip this step.
2 Press MENU to
display the
main menu
screen.
3 Press PLAY
5
or STOP
∞
(or CH
5
/
∞
on the
front panel) to select a desired fea-
ture on the menu, then press OK/
STATUS.
4 When you select a feature, go to
the section in this manual and
follow the instructions described
there.
To go back to the previous menu
screen, press REW
2
(or turn the
shuttle ring on the front panel to the
left).
To exit from the menu operations,
press MENU.
Note:
Menu operating buttons function only
when a menu is on the TV screen. When
no menus is on the TV screen, they
function differently.
Operations hereafter are described
using the buttons on the remote
control unless mentioned otherwise.
The buttons on the front panel having
the same (or nearly same) name or
same (or nearly same) mark function
exactly the same as those on the remote
control.
To be continued on the next page
VCR SET UP
TUNER SET UP
INITIAL SET UP
TAPE MANAGER
SELECT: CONFIRM: OK
END: MENU
IMPORTANT
The setup and adjustment proce-
dures explained hereafter are written
under the following conditions:
• You have turned on the TV and
selected the video channel (or
external video input).
• You have turned on the VCR.
Initial Setup
For the first time you turn on the VCR
or finish video channel setting, the
VCR automatically enters the Clock
Setting mode unless you have set it.
Make sure....
• Your VCR, TV and antenna are
connected correctly.
• The remote control operation mode
is set correctly for operating your
target component.
– Press VCR to operate the VCR.
– Press TV to operate the TV.
1Set Clock
1 Press POWER, if
necessary.The clock
setting menu appears.
2 Press PLAY
5
or
STOP
∞
to set the
time, then press OK/STATUS.
• Each time you press PLAY
5
or
STOP
∞
, the set time changes by 1-
minute intervals. If you press and hold
the button, the set time changes by 30-
minute intervals.
3 Press PLAY
5
or STOP
∞
to set the
day and month, then press OK/
STATUS.
• Each time you press PLAY
5
or
STOP
∞
, the set date changes by 1-
day intervals. If you press and hold the
button, the set date changes by 15-day
intervals.
4 Press PLAY
5
or
STOP
∞
to set
the year, then press
OK/STATUS.
• Each time you
press PLAY
5
or STOP
∞
, the set
year changes by 1-year intervals. If
you press and hold the button, the set
year changes rapidly.
5 Press MENU to exit from the menu
operations..
TIME - - : - - AM
DATE 01/01/00
SET: NEXT: OK
END: MENU
TIME 03 : 25 AM
DATE 01/01/00
SET: NEXT: OK
END: MENU
vr1010/75 00.6.29, 4:53 PM10
To Next Page
Loading...
