What to do if my Phocos Any-Grid PSW-H-5kW-230/48V Battery Charger shows that the battery is over-charged?
If your Phocos Battery Charger indicates that the battery is over-charged, return it to a repair center.
How to fix Phocos Any-Grid PSW-H-5kW-230/48V Battery Charger when the unit shuts down automatically during start-up process?
If your Phocos Battery Charger shuts down automatically during the start-up process, it's likely because the battery voltage is too low (less than 45.84V/22.92V for the 48V/24V model). To resolve this, first try to re-charge the battery. If the issue persists, you may need to replace the battery.
What to do if Phocos Any-Grid PSW-H-5kW-230/48V Battery Charger has no response after power on?
If your Phocos Battery Charger doesn't respond after you power it on, the battery voltage may be too low (less than 33.6V/16.8V for the 48V/24V model) or the battery polarity is connected in reverse. First, check if the batteries and wiring are correctly connected, paying attention to the battery polarity. Then, try recharging the battery. If the issue continues, consider replacing the battery.
Why is the internal relay of Phocos Any-Grid PSW-H-5kW-230/48V switched on and off repeatedly when the unit is turned on?
If the internal relay of your Phocos Battery Charger switches on and off repeatedly when you turn it on, the battery might be disconnected. Check if the battery wires are securely connected.
How to resolve AC output current unbalanced issue on Phocos Any-Grid PSW-H-5kW-230/48V?
To address an unbalanced AC output current on your Phocos Battery Charger: First, restart the inverter. Then, remove excessive loads and re-check load information from the LCD of the units. If the values are different between units on the same phase, check if the AC input and output cables are the same length, cross-section and material.
What to do if my Phocos Battery Charger's internal converter component is too hot?
If the temperature of the internal converter component in your Phocos Battery Charger exceeds 120°C, check if the unit's airflow is blocked or if the ambient temperature is too high.
What to do if my Phocos Battery Charger displays fault code 86?
If your Phocos Battery Charger displays fault code 86, indicating that the AC output mode setting is different between units, switch off the units and check settings menu number 28.
Why is the input voltage displayed as 0 on the LCD of my Phocos Any-Grid PSW-H-5kW-230/48V?
If the input voltage is displayed as 0 on the LCD of your Phocos Battery Charger and the green LED is flashing, it could be due to a tripped input circuit breaker, insufficient AC power quality, or another issue. Check if the AC wires are too thin or too long, and ensure that the generator (if used) is working correctly or that an input AC source exists. You can also try changing the output source priority to “Solar / PV First”.
What to do if my Phocos Battery Charger output is short circuited?
If the output of your Phocos Battery Charger is short-circuited, check if the wiring is well connected and remove any abnormal loads.
What to do if EEPROM corrupted on Phocos Any-Grid PSW-H-5kW-230/48V?
Please contact your repair center and communicate the serial number of the affected unit.
General| Output Power | 5000 W |
|---|---|
| DC Input Voltage | 48 V |
| AC Output Voltage | 230 V |
| Battery Voltage Range | 40-60V |
| MPPT Chargers | 1 |
| Max PV Input Power | 6000 W |
| Max PV Input Voltage | 500V |
| Model | Any-Grid PSW-H-5kW-230/48V |
| Rated Power | 5000 W |
| Communication | RS485, CAN |
| Type | Hybrid Inverter |
| Protection | Overload, Short Circuit, Over Temperature |
To Next Page
