8
En
INSTRUCTION MANUAL
Auto-Save Functions
The Indra360 TTL will remember studio light settings. Previous settings will be
retained each time it is turned on.
Modeling Flash
1. Pressing the camera depth-of-eld preview button (if available) will re the
studio light continuously for 1 second. The modeling ash allows you to see the
lighting eects and balance on the subject. (Please see your camera manual for
more information on the DOF button and button assignment.)
2. The modeling ash is available in all modes, TTL, Manual and Multi.
Modeling Light
The Phottix Indra360 TTL is equipped with an LED modeling light. This is
helpful for both previewing lighting set-ups and assisting with focusing in
dimly lit environments.
The Modeling Light has two modes
1. Manual mode: 9 brightness levels from 01 to 09 are available.
2. OFF mode: The modeling light will be turned o.
Please note:
1. When the studio light is ring, the modeling light will not turn o
automatically.
2. Using the modeling light uses a lot of battery power.
Adjusting the brightness of the Modeling Light
The modeling light can be turned on/o via menu option
in
or with the modeling light swtich
.
Via Menu option
1. Press Function Button 4 until appears on the LCD display.
2. Press the corresponding function button to
.
3. When the modeling light option
is selected, it will be highlighted
on the LCD display.
4. Turn the “Adjust/Set knob” to change the modeling light mode from
Manual (01-09 stop) or OFF.
5. Press the function button corresponding to
or the “Adjust/Set
knob” to conrm the settings and exit the editing mode.
Via Modeling Light Switch
1. Press the modeling light switch to turn on/o the modeling light.
2. When the modeling light is turned on the modeling light icon
will be
highlighted on the LCD display.
3. Turn the “Adjust/Set knob” to change the modeling light mode from
Manual (01-09 stop) or OFF.
4. Press “Adjust/Set knob” to conrm the settings and exit the editing mode.
Flash Modes
The Phottix Indra360 TTL Studio Light has three ash modes: TTL Auto, Manual
and Multi.
TTL Flash Mode
When the Phottix Indra360 TTL Studio Light is set to TTL mode, the studio light
will re at the selected ash mode and ash power, as set on a Phottix Odin or
other Phottix compatible ash trigger featuring power control.
Flash Exposure Compensation-FEC
The Phottix Indra360 TTL Studio Light can be used to adjust Flash Exposure
Compensation (FEC) from-3 to +3 in 1/3rd stops. This is useful in environments
where ne-tuning of the TTL system is needed.
Please note:
1. If both the triggering device (if TTL mode is available) and the studio light
are set to TTL modes and EV adjustment is set on both units, then the nal
exposure value will be the sum of the two Flash Exposure Compensation
Values.
2. If the triggering device is set to Manual mode (if available) and the studio
light is set to TTL mode with Flash Exposure Compensation Value, then the
Flash EV Value will be used to calculate the nal ash output.
Manual Flash Mode
In Manual mode the studio light will re at the power levels set. The Phottix
Indra360 TTL Studio Light can be adjusted from 1/128 to 1/1 in 1/3 stop incre-
ments (1/128, 1/64, 1/32, 1/16, 1/8, 1/4, 1/2, and 1/1). Flash modes and power
of the studio light cannot be adjusted and controlled on the triggering device.
Multi Stroboscopic Flash Mode
With Multi Stroboscopic mode a series of rapid ashes will be red. The ash
count, frequency and power of these ashes can be programmed on the
Phottix Indra360 TTL Studio Light. Multi mode is useful for capturing multiple
images of a moving subject in the same photo and for other special eects.
In Multi Stroboscopic mode, the studio light will be red at the programmed
manual ash power, ash counts (1-100), and frequency (1-100Hz). The ash
power can be set from 1/128 to 1/4 in 1/1 stop increments (1/128, 1/64, 1/32,
1/16, 1/8, and 1/4). Flash modes and power of the studio light cannot be
adjusted and controlled on the triggering device.
Please note:
1. Overheating and even damage to the ash tube can be resulted from
excessive use of the Multi Stroboscopic mode.
2. If overheated the ash will automatically increase charging time. If the
temperature continues to rise, the light will stop ring.
To Next Page
Loading...
