Piaa LP530 User Manual

-1-
PKI-0007-3
LP530
InstallationInstructions
ThankyouverymuchforpurchasingPIAAproduct.
Pleasereadthisentiremanualbeforeinstallationanduseofthisproduct.
Pleasereadthecautionarypointsbeforeinstallationtoensuresafeutilizationoftheproduct.
● Thelampandtheswitchharnessareintendedforautomobileuse.Donotuseforanyotherpurpose.
● Thislampisintendedforuseinrain(dayornight),duringfoggyorsnowyconditionswherevisibilityishampered.
Donotuseduringnormaldrivingconditions.
● Donotoperatetheswitchwhiledriving.
● Ifthelampiskeptonwhentheengineisnotrunning,itmaydrainthebattery.
● Makesurethelampisinstalledsecurelybeforedrivingthevehicle.Ifanabnormalityisfound,adjustitimmediately.
● Checkforanyloosescrewsthatholdthelampinplacebeforedriving.Ifyoufindanyloosescrewsorbolts(ifabracketis
used),tightenthemsecurely.Ifyounoticealoosepartwhiledriving,inspectthesectionimmediatelyandmakethenecessary
adjustments.
● Avoidrepeatedlyturningthelampoffandonasitmayreducetheoveralllifeofthebulb.
● Someofvehiclesareproducedhighvoltagesofelectricchargewhenyoustartengine.Avoidloadingextravoltagetolamps,
pleaseturntheswitchoffwhenyoustartengine.
● Avoidneedlessdisassemblyofthelamportheswitchharnessasitmaycauseittofail.
● Ifthelampand/ortheswitchharnessisremovedandsetasideforsafekeeping,wipeawayalldustorgrimeandstoreinan
placefreeofmoisture.
● Ifthelensiscrackedordamagedinanyway,verifywhetherthereisanydamagetotheharnessortheswitchharnessthatitis
connectedto.Ifthereisanydamagetothecordcovering,replaceitimmediately.
● Avoidinjurywhenreplacingtheharnessandtheswitchharness.Pleasedisposeofitasanon-combustibleitem.
※ The  and marksindicatedinthismanualare
cautionarypointsrelatedtotheinstallationoftheproduct.
Toensuresafeandsecureinstallationoftheproduct,pleasefollowthesepointsclosely.
Touser … Pleasekeepthismanualandareceiptwhichcanberecognizedthe
shopnameyouboughtat.
Whengivingthisproducttoathirdparty,alwaysincludethismanual
togetherwiththeproduct.
Toshopownersinstallingtheproduct … Afterinstallationoftheproduct,makesurethecustomerisprovided
withthisownerʼ smanual.
● Donottouchthebulbwhilelitorimmediatelyafterswitchingitoffbecausethelampremainsextremelyhot.Severeburnsmay
occurasaresult.Also,careshouldbetakentopreventwaterfrommakingcontactwiththelens.Thismaycausethelensto
crackorimpairproperfunctioning.
● Thelampbecomesveryhotwhenturnedon.Whenparkingyourcarnearflammableitemssuchasdriedleaves,turnoffthe
lampasitmaycauseafire.
● Donotlookdirectlyintothelightforlongperiods.Doingsomaycauseeyeirritationorvisualimpairment.

Piaa LP530 Specifications

General

Brand	Piaa
Model	LP530
Category	Automobile Accessories
Language	English

Summary

Product Details

Tools Required

Lamp Installation Preparations and Temporary Setup

Switch Harness Installation Sequence

Lamp Installation Procedures

If Using Only the Double-Side Tape

Instructions for applying double-sided tape for lamp mounting, including surface preparation and adhesion considerations.

If Using Screws to Fix Lamp Stably

Procedure for securely mounting the lamp using screws (M4 bolt or screw) with bracket attachment.

Driving and Spot Light Aiming

Fog Light Aiming

Guidelines for aiming fog lights to minimize glare and maximize road illumination, following SAE standard J583.

Troubleshooting

Lamp Does Not Activate After Installation

Steps to diagnose and resolve issues where the lamp fails to turn on, checking wiring, fuses, and switch connections.

Bulb Suddenly Fails to Light Up

Procedure for addressing a bulb failure, involving checks on vehicle wiring system fuses and switch harness fuses.

Fuse Replacement Procedures

Guidance on checking for short circuits and replacing damaged wiring or fuses in the lamp harness assembly.