Pilous ARG 250 CF User Manual

AR G 220 D − N C Automa t • AR G 220 DF − N C Automat
ARG 250 D − NC Automat • ARG 250 DF − NC Automat • ARG 250 C − NC Automat • ARG 250 CF − NC Automat
ARG 300 D − NC Automat • ARG 300 DF − NC Automat • ARG 300 C − NC Automat • ARG 300 CF − NC Automat
1. PART
INSTRUCTION MANUAL
Pilous − pásové pily, spol. s r.o., Železná 9
00 420 543 25 20 11, e−mail:pilous@pilous.cz
, 619 00 Brno, Czech Republic
tel.: 00 420 543 25 20 10, fax:

Pilous ARG 250 CF Specifications

General

Brand	Pilous
Model	ARG 250 CF
Category	Saw
Language	English

Summary

General Information and Safety

0.1. Safety Provisions

Essential safety regulations and warnings to prevent hazards during machine operation and maintenance.

0.2. Scope of Use / Use acc. to Specification

0.3. Operator Requirements and Training

Specifies the qualifications and training necessary for personnel operating the machine safely and effectively.

0.4. Machine Safety Enclosure Requirements

Details the mandatory requirements and importance of protective enclosures for machine safety.

0.5. Protective Enclosure Details

Provides specific information about the function and operation of protective enclosures on the machine.

1. Transport and Storage Procedures

2. Machine Installation Guide

2.2. Transport Beam Removal and Alignment

Step-by-step guide for removing transport beams and aligning the machine correctly.

2.4. Electrical Connection and Power Supply

Crucial information on connecting the machine to the electrical supply, including voltage and wiring.

5. Individual Unit Descriptions

5.1. Setting of Cutting Angle

5.2. Material Clamping

Procedures for correctly clamping workpieces using the machine's vice system for secure cutting.

5.2.1. Setting of Vice Clamping Force

Guidance on adjusting the clamping force of the vice for optimal material holding and preventing distortion.

5.2.4. Setting of Feeding Speed of Moving Vice

5.3. Saw Blade Guide

Information on the saw blade guidance system, including its components and function.

5.3.1. Saw Blade Replacement and Tensioning

Detailed steps for replacing the saw blade and correctly setting its tension for optimal performance.

5.3.2. Guide Head Setting

Guidance on adjusting the saw blade guide heads for proper alignment and blade lifespan.

5.4. Saw Blade Feed into Cutting Position

Instructions for setting the saw blade's feed rate into the cutting position for precise cuts.

5.5. Setting of Band Saw Head Stroke Height

6. Control Board and VISION Unit Operation

Core Control Functions Overview

Explanation of fundamental control functions like Master Switch, Total Stop, and speed controls.

VISION 120 Control Unit Details

Workpiece Parameter Setup

Instructions for programming and setting workpiece parameters for automated cutting cycles.

Manual Control Mode Operation

Basic Controls for ARG 250/300 D(F)-NC

Overview of essential controls applicable to the ARG 250/300 D(F)-NC machine models.

Saw Blade Speed Selection Switch

Main Control Menu Navigation

Workpiece Parameter Setup (ARG 250/300 C(F)-NC)

Instructions for programming workpiece parameters for the ARG 250/300 C(F)-NC models.

Basic Control Functions Overview (ARG 250/300 C(F)-NC)

Overview of fundamental controls like Master Switch, Total Stop, and mode selection for these models.

Saw Blade Speed Switch Selection

Saw Blade Speed Adjustment Controller

VISION 230 Control Unit Details

Workpiece Parameter Setup (ARG 250/300 C-NC/CF-NC)

Instructions for programming workpiece parameters for the ARG 250/300 C-NC/CF-NC models.

Manual Control Mode Operation (ARG 250/300 C(F)-NC)

Dual Vice Workpiece Clamping Procedure

7. Putting the Machine into Operation

7.1. First Cut Procedure - ARG 220 Automat

Step-by-step guide for performing the initial cut on the ARG 220 Automat machine.

7.2. First Cut Procedure - ARG 250/300 Automat

Step-by-step guide for performing the initial cut on ARG 250/300 Automat machines.

8. Error Messages and Troubleshooting

Moving Vice Feed Sensor Failures

Troubleshooting steps for errors related to moving vice feed induction sensors IS1 and IS2.

Saw Blade Elevation Error

Stop Position Error Detection

Protective Enclosure Open Error

Troubleshooting for errors triggered by an open protective enclosure during operation.

Motor Thermal Protection Error

Guidance for resolving errors related to the thermal protection of the saw blade motor.

Frequency Converter Failure

Troubleshooting steps for failures related to the frequency converter driving the motor.

Vice Pressure Faults

Saw Blade Integrity Failures

Addressing issues such as incorrect saw blade tension or a broken saw blade.

9. General Failures and Their Solutions

Electrical Installation Faults

10. Machine Maintenance and Checks

11. Saw Blade Information

11.2. Saw Blade Tooth Size Recommendations

Recommendations for selecting the appropriate saw blade tooth size based on material and section.

11.3. Workpiece Clamping for Optimal Cutting

Guidance on workpiece clamping techniques to improve cutting quality and saw blade lifespan.

11.4. New Saw Blade Running-in Procedure

11.5. Factors Affecting Saw Blade Lifespan

Identification of factors that influence the lifespan and performance of the saw blade.

11.6. Recommended Cutting Speed and Feed Values