Setting up08
30
En
Note
• Using the “By Satellite” option for channel scanning may fail in
some cases. If this is the case, select “All Frequencies” or
“SMATV”.
• If you access “Satellite Setup” through “Auto Installation”, three
buttons – “Add New Channels”, “Replace Existing Channels”
and “Reset” – are unavailable.
• Selecting “SMATV” (Satellite Master Antenna Television system)
causes your flat screen TV to make an attempt to obtain all
available channels regardless of antenna setting.
8 Select “Aerial Select” (
/
).
Use / to select “Single”, “DiSEqC 1”, “DiSEqC 2”, “DiSEqC 3”,
“DiSEqC 4”, “Tone Burst 1” or “Tone Burst 2”.
9 Select “Satellite Select” (
/
then ENTER).
10 Select “Satellite” (
/
then ENTER).
Information on the selected satellite appears on screen. Select an
available satellite from the list.
Units for LNB Frequency is MHz.
This option is available only if you select “By Satellite” in step 7.
Select “New 1” through “New 5” then press and hold
ENTER
to
display the software keyboard.
11 Select “LNB Frequency” (
/
).
Use / to select “Universal” (having two LNB frequencies - 9750/
10600, default) or use buttons 0 to 9 (then press
ENTER
) to enter a
frequency if you select “---”.
This option is available only when you select “All Frequencies” or
“By Satellite” in step 7.
12 Select “LNB Voltage” (
/
).
Use / to select “On” or “Off” (default).
Select “On” in most cases.
13 Press RETURN then select “Transponder” (
/
).
14 Select “Transponder Type” (
/
).
Use / to select “All” for all transponders of the selected
satellites (default), “One” for only one transponder, or “Manual” for
transponders specified.
15 Select “Frequency” (
/
).
The option selected in step 14 appears with available transponders
for the satellite selected on the satellite list in step 10.
Enter a frequency using buttons 0 to 9 (then press
ENTER
) if you
select “Manual” in step 14.
16 Select “Polarization” (
/
).
Use / to select “Horizontal” (default) or “Vertical”.
17 Select “Symbol Rate” (
/
).
Use / to select “22000” (default), “27500” or use buttons 0 to 9
(then press
ENTER
) to enter a symbol rate.
Note
• “Polarization” and “Symbol Rate” options are only available if
you select “Manual” from “Transponder Type” in step 14.
18 Press RETURN then select “Signal Check” (
/
then ENTER).
Use / to select the desired satellites from the satellite list or
transponders for the selected satellites.
Note
• If you access “Signal Check” through “Auto Installation”, the
button “Add” is unavailable (see page 45).
• Units for Transponder is MHz.
To search and register new channels, select “Add New Channels”
(see page 45).
To replace registered channels with new channels, select “Replace
Existing Channels” (see page 45).
“Reset” restores all satellite settings to factory default values.
19 Press HOME MENU to exit the menu.
Reset
Replace Existing Channels
Add New Channels
Scan Type : By Satellite
Aerial Select : Single
Satellite Select
Transponder
Signal Check
Satellite : Astra1
LNB Frequency : Universal
LNB Voltage : Off
Level
: 60%
Quality : 80%
Transponder Type : Manual
Frequency : ---- MHz
Polarization : Horizontal
Symbol Rate : 22000 KS/s
Add
Satellite : Astra1
Transponder : 10000
Level
:
88%
Quality :100%
PDP-LX609H.book Page 30 Wednesday, August 6, 2008 4:00 PM
Downloaded From TV-Manual.com Manuals
To Next Page
Loading...
Need help?
General
