The provided document is a workshop manual for the Planet Eclipse Ego LV2 paintball marker, detailing its components, assembly, and troubleshooting procedures.
Function Description
The Planet Eclipse Ego LV2 is a high-performance paintball marker designed for competitive and recreational use. It operates by using compressed air or nitrogen to propel .68 inch calibre paintballs. The marker features an electronic ON/OFF button as its disabling device and incorporates various sub-assemblies for precise operation, including a bolt and rammer assembly, HP and LP regulator assemblies, a solenoid assembly, a frame sub-assembly with a circuit board, a trigger assembly, a valve assembly, a POPS (Push On Purge System) assembly, a feedneck assembly, and a breech sensor (BS) assembly. The marker is designed for reliability and ease of maintenance, with clear instructions for cleaning, inspection, lubrication, and part replacement.
Important Technical Specifications
- Calibre: 0.68 inch paintballs only.
- Propellant: Compressed air/nitrogen only (CO2 or other pressurised liquids are not to be used).
- Velocity: Adjustable, not to exceed 300 feet (91.44 metres) per second or local/national laws.
- O-Rings: Various NBR70 and NBR90 O-rings are specified throughout the marker, including:
- Bolt and Rammer Assembly: 014 NBR70, 14X2 NBR70, 013 NBR70, 012 NBR70, 011 NBR70, 010 NBR70.
- HP and LP Regulator Assemblies: 013 NBR70, 008 NBR70 (internal), 7X1 NBR70, 007 NBR70, 014 NBR70, 011 NBR70.
- Solenoid Assembly: 4X1 NBR70.
- Valve Assembly: 5X1 NBR70, 013 NBR70, 3X1 NBR70, 017 NBR70.
- POPS Assembly: 007 NBR70, 004 NBR70, 005 NBR90.
- Feedneck Assembly: 006 NBR70, 004 NBR70.
- Screws:
- Solenoid Assembly: M2.5x5 Cap Head Screw, M1.7x16 Cross Pan Head Screw.
- Frame Sub-Assembly: #10-32 x 0.375 Socket Button Head Screw, M2x8 Button Head Screw, M2.5x5 Cap Head Screw.
- Trigger Assembly: M2.5x5 Cap Head Screw, #6-32 x 0.125 Socket Grub Screw, #6-32 x 0.5 Socket Grub Screw.
- Valve Assembly: #10-32 x 0.375 Socket Button Head Screw.
- POPS Assembly: #10-32 x 1 Socket Cap Head Screw.
- Feedneck Assembly: #10-32 x 0.5 Socket Cap Head Screw.
- Circuit Boards: MME LV2 GUI Board, MME LV2 Comms Board, MME LV2 Main Board.
- Battery: 9V Battery Board.
Usage Features
The Ego LV2 is designed for user-friendly operation and includes several features to enhance the paintball experience:
- Electronic ON/OFF Button: Serves as the primary disabling device for safety.
- Breech Sensor (BS) Assembly: Helps detect paintballs in the breech, ensuring proper firing.
- POPS Assembly: A Push On Purge System for quick and easy de-gassing of the marker.
- Adjustable Regulators: HP (High Pressure) and LP (Low Pressure) regulators allow for fine-tuning of the marker's performance and velocity.
- Feedneck Assembly: Designed for secure attachment of a paintball loader, featuring a thumb wheel and clamping feed screw for adjustment.
- Trigger Assembly: Includes a trigger body, shoe, spring, and magnet carrier for a responsive and customizable trigger pull.
- Bolt Pin: Allows for quick removal and installation of the bolt and rammer assembly for maintenance.
Maintenance Features
The manual provides comprehensive guidance for maintaining the Ego LV2, emphasizing regular cleaning, inspection, lubrication, and replacement of highlighted seals and faces.
- Service Indicators: Specific sections detail "Lubrication Required" and "Service Required" for various components, indicating which parts need attention.
- Component-Specific Maintenance:
- Bolt and Rammer Assembly: Requires cleaning, inspection, and lubrication of all O-rings (014 NBR70, 14X2 NBR70, 013 NBR70, 012 NBR70, 011 NBR70, 010 NBR70) and the rammer bumper.
- Regulator Assemblies (HP and LP): Involves cleaning, inspection, and lubrication of O-rings (013 NBR70, 008 NBR70, 007 NBR70, 7X1 NBR70, 014 NBR70, 011 NBR70), seals (LPR Seal, HPR Seal, SL3 Reg Seal), and components like the LPR piston, HPR piston, and purge poppet.
- Valve Assembly: Requires cleaning, inspection, and lubrication of O-rings (5X1 NBR70, 013 NBR70, 3X1 NBR70, 017 NBR70) and the exhaust valve.
- Solenoid/Manifold: Inspection of manifold-body gasket, solenoid-manifold gasket, and 4X1 NBR70 O-rings for leaks.
- Breech Sensor (BS) Assembly: Detents (active and spare) should be inspected.
- Troubleshooting Guides: The manual includes sections for common issues such as:
- Leaks Down the Barrel: Often related to the exhaust valve, valve guide, or 013 NBR70 O-ring.
- Bolt Stays Forward and Leaks Down the Barrel: Requires de-gassing, cycling the bolt manually, and re-gassing.
- Marker Fires But Bolt Does Not Move: Typically due to an unengaged bolt pin, requiring proper alignment and engagement.
- Bolt 'Pops Up' When Firing: Check the lever assembly in the body.
- Solenoid/Manifold Leak: Inspect gaskets and O-rings.
- Constant High/Low Velocity: Involves checking regulator seals, pistons, purge poppet, manifold-body gasket, LP hose routing, valve guide, and bolt insert orientation.
- Inline Regulator Leak: Requires inspection of various O-rings, regulator plug, gasket, and frame gasket.
- Breaking Paint in the Breech: Check detents and bolt tip.
- Inconsistent Shot to Shot FPS: Inspect HPR/LPR seals, pistons, and frame filter.
- Inefficient / 'Airy' Sound to Shot: Check dwell value, LPR setting, and SFR setting, and solenoid-body gasket installation.
- Safety Precautions: Emphasizes wearing eye protection, using a barrel blocking device, never looking into the barrel, and ensuring the marker is de-pressurised before maintenance. All installations, modifications, or repairs should be carried out by qualified individuals at licensed facilities.
Need help?
General
To Next Page