POSIFLEX PD – 2600 User Manual

Part 1
FCC Notes:
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions manual, may cause interference to radio
communications. It has been tested and found to comply with
limits for a Class A digital device pursuant to subpart J of Part
15 of FCC Rules, which are designed to provide reasonable protection against
interference when operated in a commercial environment. Operation of this equipment
in a residential area is likely to cause interference in which case the user at his own
expense will be required to take whatever measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
About This Manual:
Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex will assume no liability for any technical inaccuracies or editorial or other
errors or omissions contained herein, nor for direct, indirect, incidental, consequential
or otherwise damages, including without limitation loss of data or profits, resulting
from the furnishing, performance, or use of this material.
This information is provided “as is” and Posiflex Technology, Inc. expressly disclaims
any warranties, expressed, implied or statutory, including without limitation implied
warranties of merchantability or fitness for particular purpose, good title and against
infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex reserves the right to alter product
designs, layouts or drivers without notification. The system integrator shall provide
applicative notices and arrangement for special options utilizing this product. The user
may find the most up to date information of the hardware from web sites:
http://www.posiflex.com or http://www.posiflex.com.tw
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,
disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Inc. the publisher of this documentation.
© Copyright Posiflex Technology, Inc. 2011
All brand and product names and trademarks are the property of their respective holders.
PD – 2600 / 2601 / 2602 / 2603 Series
User’s Manual
Rev. D0
P/N:
1946090
115
0

POSIFLEX PD – 2600 Specifications

General

Display Size	15 inch
Display Type	TFT LCD
Resolution	1024 x 768
USB Ports	4
Serial Ports	2
Processor	Intel Celeron
RAM	4GB
Storage	64GB SSD
Operating System	Windows 10
Connectivity	Ethernet, USB, Serial
Ethernet	10/100 Mbps
Parallel Port	1
Power Supply	12V/5A

Summary

FCC Notes

Warranty Limits

Details terms under which the product warranty is voided.

About This Manual

Explains the manual's content, disclaimers, and update policy.

Brief Introduction

The Product

Overview of the PD-2600/2601/2602/2603 series pole mount customer displays.

Features

Highlights key technical and functional features of the customer display.

Installation Guides

Host System Preparation

Instructions for preparing the host system for serial or USB interface connections.

Installing PD-2600

Details connection and setup for the PD-2600 stand-alone model.

Installing PD-2601

Steps to install the PD-2601 customer display on compatible POS systems.

Installing PD-2602

Procedure for installing the PD-2602 customer display onto KS or TP systems.

Installing PD-2603

Instructions for installing the PD-2603 customer display onto FT systems.

Command Emulation Mode Setup

DIP Switch Window

Location of the DIP switches used for command mode selection.

Using the Customer Display

Interface Selection

Guidance on choosing between RS232 and USB interfaces for the display.

Command Mode Selection Guide

Compares different command modes for application compatibility.

Driver Installation

Instructions for installing OPOS or JPOS drivers for RS232 and USB models.

Specification

Optical Specifications

Details of the display's optical characteristics, like digits and size.

Mechanical Specifications

Physical dimensions and height variations for different models.

Electrical Specifications

Power requirements and input specifications.

Environmental Specifications

Operating and storage conditions for temperature and humidity.