EasyManua.ls Logo

Poulan Pro 2050WT - User Manual

Poulan Pro 2050WT
18 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1950 / 1975 / 2050 / 2055 / 2075
2150 / 2155 / 2175 / 2350 / 2375
2050WT / 2150PR
Electrolux Home Products, Inc.
104 Warren Road
Augusta, GA 30907
ENGLISH
ESPAÑOL
FRANÇAIS
530164603 6/16/04
R
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1--800--554--6723
www.poulan.com
For Occa si onal U s e On ly
Copyright E2004 Electrolux Home Products, Inc.
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
WARNING:
Read and follow all Safet y Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e en-
strucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Electrolux Canada Corpor ation
6150 McLaughlin Road
Mississauga, Ontario L5R 4C2

Table of Contents

Questions and Answers

  • J
    Jack KnappAug 11, 2025
    Why won't my Poulan Pro Chainsaw start?
    • C
      Crystal JonesAug 11, 2025
      If your Poulan Pro Chainsaw won't start, several factors could be the cause: * The ignition switch might be off; move it to the ON position. * The engine could be flooded; refer to the “Difficult Starting” section in the Operation Section. * The fuel tank may be empty; refill it with the correct fuel mixture. * The spark plug might not be firing; install a new spark plug. * Fuel may not be reaching the carburetor; check for a dirty fuel filter and replace if necessary, or check for kinked or split fuel lines and repair or replace them.
  • W
    wwagnerAug 17, 2025
    Why Poulan Pro 2050WT Chainsaw engine will not idle properly?
    • D
      Daniel GilbertAug 17, 2025
      If your Poulan Pro Chainsaw engine won't idle properly, it could be due to the following reasons: * The idle speed may need adjustment; see “Carburetor Adjustment” in the Service and Adjustments Section. * The carburetor may require adjustment; contact an authorized service dealer for assistance.
  • E
    Edward BaileyAug 25, 2025
    What to do if Poulan Pro 2050WT chain moves at idle speed?
    • E
      Elizabeth HolderAug 25, 2025
      If the chain on your Poulan Pro Chainsaw moves at idle speed, it could be due to: * Idle speed requiring adjustment; see “Carburetor Adjustment” in the Service and Adjustments Section. * The clutch requiring repair; contact an authorized service dealer.
  • M
    Michelle MillerAug 29, 2025
    What to do if Poulan Pro 2050WT Chainsaw won't accelerate?
    • C
      Cindy SmithAug 29, 2025
      If your Poulan Pro Chainsaw won't accelerate, lacks power, or dies under a load, consider these potential causes: * The air filter may be dirty; clean or replace it. * The spark plug might be fouled; clean, replace, and regap the plug. * The chain brake could be engaged; disengage it. * The carburetor may require adjustment; in this case, it is recommended to contact an authorized service dealer.
  • J
    Jonathan RiveraSep 4, 2025
    How to fix excessive smoke from Poulan Pro Chainsaw?
    • W
      William HarringtonSep 4, 2025
      Excessive smoke from your Poulan Pro Chainsaw usually indicates too much oil mixed with the gasoline. To resolve this, empty the fuel tank and refill it with the correct fuel mixture.

Poulan Pro 2050WT Specifications

General IconGeneral
Displacement50 cc
Power SourceGasoline
Engine Type2-Cycle
Bar Length20 inches
Oil Capacity8.5 fl oz
Chain Pitch0.325 inches
Chain Gauge0.050 inches

Related product manuals