Poulan Pro P3516PR User Manual

Poulon
?
I
Manual de
Instrucciones
Man uel d'l
nstructions
P331
4
lP3314WS /
P3314WSA
P3416
/
P3516PR
/
P4018WM
P4O18WT
/
P3818AV
P4O1
8AV
/
P4O1 8AV
BH
For Occasional
Use
Only
WARNING:
Read
and
follow
all Safety
Rules and Operating
Instructions before
using
this
product.
Failure
to do so can
result
in
serious
injury.
ADVERTENCIA:
Lea
el
manual de instrucciones
y
srga
todas
las
advertencias
e en-
strucciones
de seguridad.
El no hacerlo
puede
resultar en
lesiones
graves.
AVERTISSEMENT
Lire
le manuel d'instructions
et bien
respecter
tous les avertisse-
ments
et
toutes
les instructions de
s6curit6.
Tout d6faut de
le
faire
oourrait entrainer
des blessures
oraves.
Please
do
not return
product
Por
favor,
no
devuelva
el
pro
Veuillez
ne
pas
retourner
le
P
1
-800-55
Register
your
product
online
Registre
su
producto
en
linei
Enregistrez
votre
produit
en
www.pou
Instruction
Manual
luct
to retailer.
producto
al
lugar
de
compra.
le
produit
au d€taillant.
,554-6723
line at:
inea en:
en
ligne d
I'adresse :
oulan.com
Poulan
9335
Harris Corners
Parkway
Charlotte,
NC 28269
Poulan
850
Matheson Blvd.
West
Mississauga, Ontario
L5V 084
545186804
Rev.
B
1131111
BRW

Poulan Pro P3516PR Specifications

General

Engine Type	2-Stroke
Engine Displacement	35 cc
Bar Length	16 in
Power Output	2.1 HP
Weight	10.5 lbs
Chain Pitch	0.325 inches
Chain Gauge	.050 in
Oil Capacity	6.8 fl oz

Summary

Poulan Chainsaw Manual Introduction

Customer Service and Product Models

Contact information and list of covered chainsaw models.

General Safety Warning

Crucial initial safety advice before product use.

Safety Symbols and Starting Guide

Understanding Safety Symbols

Explains visual indicators for safety and operation.

Engine Starting Procedure

Step-by-step guide for initiating the engine.

Safe Operation and Kickback Awareness

Personal Protective Equipment (PPE)

Details essential safety gear for operation.

Safe Handling, Fueling, and Kickback

Guidelines for safe operation, fueling, and kickback prevention.

Kickback Mitigation and Control

Understanding Kickback Types

Describes pinch-kickback and pull-in.

Maintaining Operational Control

Techniques for safe grip, balance, and control.

Kickback Safety Features

Protective Features: Bar, Chain, Brake

Details features reducing kickback and stopping the chain.

Computed Kickback Angle (CKA)

Explains CKA values and their safety implications.

Assembly and Technical Specifications

CKA Table and Emissions Compliance

Lists CKA values and emission compliance details.

Attaching the Bar and Chain

Step-by-step guide for installing the guide bar and chain.

Bar, Chain, and Tensioning

Guide Bar and Chain Installation

Continues mounting the guide bar and chain.

Chain Tension Adjustment Procedure

How to check and adjust chain tension properly.

Chain Saw Components and Controls

Component Identification Diagram

Labels and identifies the main parts of the saw.

Key Control Functionality

Explains the purpose of key operating controls.

Pre-Operation Checks and Fueling

Control Operation Details

Describes throttle lockout, choke, primer, brake.

Fueling Procedures and Warnings

Guides on safe fueling and correct fuel mix.

Engine Starting Procedures

Starting Cold, Warm, or Flooded Engines

Step-by-step for cold, warm, and difficult starts.

Operating Tips and Tree Felling Introduction

Chain Brake Testing and Operation

How to test and use the chain brake.

General Operation and Felling Safety

Advice for safe use and tree felling precautions.

Tree Felling and Bucking Techniques

Felling Planning and Notching

Planning retreat paths and cutting felling notches.

Bucking Fallen Trees Overview

Basic principles for cutting fallen trees.

Bucking, Limbing, and Pruning Methods

Bucking Methods

Cutting logs with or without support.

Limbing and Pruning Safety Guidelines

Safe practices for removing branches.

Service and Maintenance Schedule

Limbing and Pruning Guidelines

Specifics on safe limbing and pruning.

Routine Maintenance Checklist

Schedule of required checks and cleaning.

Component Checks and Cleaning

Fastener, Chain, and Bar Checks

Verifying fasteners, chain sharpness, and guide bar condition.

Fuel, Lubrication, and Air Filter Checks

Checking fuel mixture, lubrication, and air filter.

Parts Service and Chain Maintenance

Muffler, Plug, and Filter Service

Replacing or cleaning key engine components.

Chain Adjustment and Sharpening

Detailed steps for chain care.

Advanced Adjustments and Cooling System

Chain Sharpening Techniques

In-depth guide to sharpening the saw chain.

Carburetor and Cooling System Care

Adjusting the carburetor and maintaining the cooling system.

Storage and Fuel System Preparation

General and Seasonal Storage

Procedures for storing the saw for short or long periods.

Fuel System and Engine Storage

Preparing fuel system and engine for storage.

Troubleshooting Common Issues

Problem, Cause, and Remedy Guide

A table for diagnosing and fixing common problems.

Limited Warranty Information

Warranty Coverage and Claim Process

Details warranty terms, exclusions, and how to file a claim.

Warranty Rights and Emissions Compliance

Owner Responsibilities and Emissions Warranty

Outlines owner duties and the emissions system warranty.

Emissions Control Warranty Details

Manufacturer and Owner Responsibilities

Clarifies duties for the emissions warranty.

Product Label Emission Information

Explains emission certification details on the product label.

Warranty Claims and Parts

Filing Claims and Service Locations

How to file claims and find service centers.

Emission Control Parts List

Lists components covered by the emissions warranty.