EasyManua.ls Logo

Poulan Pro PR5020 User Manual

Poulan Pro PR5020
60 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
a WARNING! Read and follow all Safety Rules and
Operating Instructions before using this product.
Failure to do so can result in serious injury.
Instruction Manual
PR5020
Quick-Start Guide
NOTE: Your product may differ slightly from the item shown.
1
Mix 2.6 oz. of full synthetic 2-Cycle Oil with 1 gallon of fresh seasonal
gasoline for a 50:1 mixture. Shake well. Pour into fuel tank.
CAUTION: Do not use alternate fuels such as ethanol blends above
10% by volume (E-15, E-85) or any methanol blended fuel.
2
Add bar and chain oil to oil tank
until full.
3
Make sure chain brake is locked by
pushing forward on handguard.
4
Slowly press primer (air purge) bulb
10 times.
5
Pull blue choke lever out fully.
6
Place right foot in rear handle as shown.
Using right hand, pull starter rope sharply
until machine attempts to start, or a maximum
of 5 times.
7
Push blue choke lever to half choke
position.
8
Pull starter rope until engine starts.
9
Allow engine to warm for 30 seconds.
10
Make sure chain brake is unlocked by
pulling back on handguard.
11
Squeeze throttle trigger to set normal
idle. Your chainsaw is now ready
for use.
12
Press red switch to STOP position
ZKHQ¿QLVKHGXVLQJVDZ
STARTING A WARM ENGINE
4 + 5 + 7 + 8
NOTE: If the product does not restart, the problem could be overheated
IXHO7R¿[WKLVSUREOHPWU\WKHIROORZLQJSURFHGXUH
1. Set the product in a cool area away from direct sunlight.
2. Allow the product to cool for at least 20 minutes.
3. Press primer (air purge) bulb repeatedly for 10-15 seconds.
4. Follow the cold starting procedure.
Repeat this procedure if the problem still exists.
NOTE: Always use fresh seasonal fuel and shorten operation time
during unseasonably warm weather.
IMPORTANT:
Never let your saw chain come in contact with soil/dirt during
operation. This will completely dull your chain and will require
installation of a new chain.
Check your chain tension prior to each time you start the chainsaw.
&KHFNWHQVLRQRQDQHZFKDLQDIWHUWKH¿UVWPLQXWHVRI
operation. See the manual for chain tensioning instructions.
LDAV50MC115817295 Rev. D 2019-01-23

Questions and Answers:

Poulan Pro PR5020 Specifications

General IconGeneral
Engine Displacement50 cc
Bar Length20 inches
Power SourceGasoline
Weight17 lbs
Engine Type2-stroke
Warranty2 years
Chain Pitch0.325 in
Chain Gauge0.050 inches
Oil Tank Capacity8.5 fl oz

Summary

Quick-Start Guide

Cold Engine Starting

Step-by-step instructions to start a cold engine.

Warm Engine Starting & Operation

Guide to starting a warm engine and general operation.

Symbols and Safety Icons

Know Your Machine Components

Chainsaw Safety Overview

Introduction to Safety Risks

Overview of chainsaw dangers and precautions.

Safe Operation Planning

Advice on preparation and protective gear.

Kickback Hazards and Control

Understanding Kickback Types

Explains rotational, pinch, and pull-in kickback.

Preventing Kickback Risks

Tips to reduce kickback occurrence.

Maintaining Operator Control

Proper grip, stance, and balance.

Kickback Safety Features & Assembly

Chainsaw Safety Features

Details on chain brake, guards, and low-kickback components.

Attaching Bumper Spike

Procedure for installing the bumper spike.

Attaching Bar and Chain

Steps for mounting the guide bar and chain.

Chain Tension Adjustment

Checking Chain Tension

Method to verify correct chain tension.

Adjusting Chain Tension

Detailed steps for setting chain tension.

Fueling and Lubrication

Safe Engine Fueling

Guidelines for mixing fuel and safe refueling.

Bar and Chain Lubrication

Importance and method of lubricating bar/chain.

Starting and Stopping

Cold Engine Starting

Comprehensive procedure for starting a cold engine.

Warm Engine Starting

Procedure for starting a warm engine.

Difficult Engine Starting

Troubleshooting for flooded engines.

Working Techniques

Practicing Cutting Techniques

Basic methods for getting started.

Tree Felling Planning

Safety and preparation for felling trees.

Tree Felling and Bucking

Notch Method for Felling

Technique for directing tree fall.

Bucking Fallen Trees

Cutting logs to desired sizes.

Bucking and Limbing

Bucking Techniques

Methods for cutting logs with/without support.

Limbing and Pruning Safety

Rules for cutting branches safely.

Maintenance and Procedures

Maintenance Schedule

Recommended service intervals and checks.

Maintenance Procedures

Specific checks like damaged parts and fasteners.

Component Checks and Cleaning

Fastener, Chain & Bar Checks

Inspecting parts for wear and tightness.

Guide Bar Maintenance

Cleaning and maintaining the guide bar.

Air Filter Cleaning

Procedure for cleaning the air filter.

Cleaning, Adjustments & Cooling

Spark Arresting Screen Cleaning

How to clean the screen.

Spark Plug Replacement

Steps for replacing the spark plug.

Carburetor Adjustment

Adjusting idle speed and engine performance.

Chain Sharpening

Sharpening Cutting Teeth

Technique for sharpening chain teeth.

Adjusting Depth Gauge

Setting the depth gauge for optimal cutting.

Troubleshooting Guide

Troubleshooting Table

Common problems, causes, and remedies.

Storage and Engine Care

Resetting Chain Brake

Procedure to reset the chain brake.

Storage Procedures

Guidelines for storing the saw.

Engine Storage Preparation

Steps to prepare the engine for storage.

Technical Data Specifications

Related product manuals