Power Fist 8699159 - User Manual

Questions and Answers

G
Gabriela StephensAug 17, 2025
Why my Power Fist 8699159 won't start?
- A
  Ashley CrawfordAug 17, 2025
  If your Power Fist Saw won't start, there are several potential causes: 1. Ensure the power cord is securely plugged in. 2. Verify that the outlet has power. If it does, turn off the saw and check the circuit breaker. If the breaker is tripped, confirm the circuit's capacity is suitable for the saw and that no other devices are overloading the circuit. 3. If your saw has a thermal reset breaker, turn it off and let it cool down before pressing the reset button. 4. Internal damage or wear may be present. In this case, have a qualified technician service the saw.
K
kbarkerAug 20, 2025
What to do if my Power Fist 8699159 Saw is overheating?
- M
  Marie FrancisAug 20, 2025
  If your Power Fist Saw is overheating, consider the following: * Avoid forcing the saw to work too quickly; allow it to operate at its own pace. * Replace a dull or damaged saw blade. * Clear any dust from the motor housing vents using compressed air. * If using an extension cord, ensure it has the correct diameter for its length and load; otherwise, eliminate the extension cord. * Adjust the saw blade and V-belt tension gradually until optimal tension is achieved. * Consult the manual for the recommended blade type if your blade is too coarse or fine for the workpiece. * Adjust the gears so that the worm is in the center of the gear. * Check the oil bath to ensure proper lubrication of the gears.
P
Paige MathewsAug 22, 2025
How to fix Power Fist Saw if the blade cuts crooked?
- A
  Alexander TorresAug 22, 2025
  If the Power Fist Saw blade cuts crooked, here's what you can do: 1. Adjust the vise so it is square with the blade and always clamp the work tightly. 2. Reduce pressure by increasing spring tension on the side of the saw. 3. Adjust the guide bearing to 0.001 in. greater than the maximum saw blade thickness, including the weld of the saw. 4. Gradually increase saw blade tension until optimal tension has been achieved. 5. Move the blade guide as close to the workpiece as possible. 6. Replace the saw blade if it is dull. 7. Check the manual for recommended speeds if the saw blade turns too quickly or slowly for the workpiece. 8. Adjust the saw blade tracking if the saw blade tracks too far away from the wheel flanges.
S
Samantha WhiteAug 26, 2025
What to do for premature blade dulling of Power Fist 8699159?
- C
  Chelsea DownsAug 26, 2025
  To address premature blade dulling on your Power Fist Saw: 1. Check the manual for the recommended blade type and replace it with an appropriate saw blade if the current one's teeth are spaced too widely for the workpiece material. 2. Try the next lower speed if the saw blade turns too quickly. 3. Increase pressure by reducing spring tension on the side of the saw if the body frame descends too lightly. 4. Reinstall the saw blade properly if it is installed backward. 5. Gradually increase saw blade tension until optimal tension has been achieved if there is insufficient saw blade tension.
A
Aaron ChapmanAug 28, 2025
How to prevent excessive blade breakage on Power Fist 8699159 Saw?
- G
  gbryantAug 28, 2025
  If you're experiencing excessive blade breakage with your Power Fist Saw: 1. Tighten the blade tension if the saw blade is loose. 2. Check the manual for the correct blade speed if the saw blade turns too quickly or slowly. 3. Clamp the workpiece securely if the vise is not gripping it. 4. Adjust the saw blade tracking if the wheel flange is eroding the saw blade. 5. Consult the manual for the recommended blade type if the saw blade teeth are spaced too widely for the workpiece material. 6. Allow the blade to reach full speed before feeding material into it. 7. Adjust the blade guides if they are poorly aligned.
D
Dr. Thomas RodgersAug 31, 2025
Why does the blade twist on my Power Fist 8699159 Saw?
- J
  Julie LeeAug 31, 2025
  If the blade on your Power Fist Saw twists, consider these solutions: 1. Reduce pressure by increasing spring tension on the side of the saw if the saw blade is caught in the workpiece cut. 2. Gradually adjust the saw blade tension until optimal tension has been achieved if the saw blade tension is too high.
J
Jasmine McgrathSep 2, 2025
Why Power Fist Saw performance decreases over time?
- T
  teresa30Sep 2, 2025
  If the performance of your Power Fist Saw decreases over time: 1. Replace the saw blade if it is dull or damaged. 2. Have a qualified technician replace the carbon brushes if they are worn or damaged.
M
Mallory VasquezSep 5, 2025
How to prevent Power Fist 8699159 Saw blade from cutting rough?
- D
  Douglas ChaneySep 5, 2025
  If your Power Fist Saw blade cuts rough: 1. Change the speed with the motor’s V-belt if the saw blade turns too quickly. 2. Reduce pressure by increasing spring tension on the side of the saw if the feed pressure is too heavy. 3. Check the manual for the recommended blade type and replace it with a more appropriate saw blade if the saw blade teeth are spaced too widely for the workpiece material.
K
Kari McdowellSep 8, 2025
Why does my Power Fist 8699159 operate slowly?
- R
  robertsonmichaelSep 8, 2025
  If your Power Fist Saw operates slowly, it may be due to an extension cord that is too long or has a wire size that is too small. Eliminate the use of an extension cord if possible. If an extension cord is necessary, use one with the proper diameter for its length and load.
V
Valerie LawsonSep 12, 2025
What causes excessive noise or rattling in my Power Fist 8699159?
- A
  Aaron DiazSep 12, 2025
  If your Power Fist Saw is making excessive noise or rattling sounds, it is likely due to internal damage or wear, such as worn carbon brushes or bearings. In this case, have a technician service the tool.