Power smart PSSAM24BS

Questions and Answers

J
Justin HarrisonAug 17, 2025
Why is the auger on my Power smart PSSAM24BS not rotating or blowing snow effectively?
- J
  Jessica CoxAug 18, 2025
  If the auger on your Power smart Snow Blower isn't rotating when engaged, or if you're experiencing poor snow blowing performance, start by cleaning the chute and inside the auger housing. Check and replace any broken auger shear pins. Remove any foreign objects obstructing the auger or impeller. Inspect the auger belt for looseness, slippage, wear, or damage and replace if necessary. Also, check the auger belt tension cable and repair, adjust, or replace it if needed. Damaged or bent auger blades should be replaced. Examine the auger gearbox for mechanical damage or binding, repairing or replacing parts and lubricating as necessary. Replace a damaged impeller or shear pins. Finally, ensure you're not moving too fast, allowing the engine to maintain speed.
A
Amy HudsonAug 21, 2025
What causes my Power smart PSSAM24BS Snow Blower engine to run rough, stall, or lose power?
- R
  Raymond OrozcoAug 21, 2025
  If your Power smart Snow Blower engine runs erratically, stalls, or seems low on power, start by emptying and cleaning the fuel tank and carburetor, then refill with fresh gasoline, as old fuel may be the cause. Check for and clear any blockages in the fuel system or line. The carburetor may need cleaning. Ensure the spark plug wire is securely connected. Inspect the spark plug, cleaning, adjusting the gap, or replacing it if faulty. If the engine oil is overfilled, drain it to the correct level; it should not be above the top two threads of the LOWER fill plug. Conversely, if the oil level is low or empty, add oil.
M
Megan OdonnellAug 25, 2025
Why does the auger belt keep breaking on my Power smart PSSAM24BS?
- K
  kurt68Aug 25, 2025
  If the auger belt on your Power smart Snow Blower is broken or repeatedly fails, first check and replace the auger tension pulley arm return spring if it's broken or missing. Ensure the auger tension pulley arm isn't stuck or binding, repairing or replacing it as necessary. Also, check for misalignment or damage to the auger tension pulley arm or pulley, repairing, replacing, or aligning them as needed. Clean any foreign material like oil, grease, or dirt from the pulleys and belt, and replace the belt if necessary. Replace or align any misaligned, loose, damaged, or bent auger pulleys. Ensure you are using the correct size and type of auger belt. Finally, adjust the belt guide pin to within 1/8 to 3/16 inches from the pulley to keep the belt in place when disengaged.
N
nicholsbrookeAug 28, 2025
Why does my Power smart PSSAM24BS have no drive movement?
- G
  gjohnsAug 28, 2025
  If your Power smart Snow Blower has no forward or reverse drive movement when the drive handle is engaged, check the drive belt tension pulley for damage or incorrect tension and repair or replace as needed. Replace the drive belt if necessary. If the friction drive wheel is worn or damaged, replace it. If the friction drive wheel is wet or slipping, allow the snow blower to dry and warm up, or adjust the drive cable tension.
L
Lori MillerAug 31, 2025
Why is the drive speed control on my Power smart PSSAM24BS Snow Blower stuck?
- L
  Leslie MonroeAug 31, 2025
  If the drive speed control on your Power smart Snow Blower is stuck in gear or won’t change gears, inspect the speed control lever and cables for damage, looseness, or missing parts, and repair or replace them as needed. Make sure the pivot stud spring tension is correct, and adjust the pivot nut spring tension if necessary. Also, check the speed control cables for looseness, damage, or binding, and repair, adjust, or replace them as needed.
A
Alicia JamesSep 3, 2025
What to do if drive engaged when drive control handle released on Power smart PSSAM24BS Snow Blower?
- J
  Jennifer GrahamSep 3, 2025
  If the drive on your Power smart Snow Blower remains engaged when the drive control handle is released, it could be due to a binding drive control cable, which needs repair or replacement. Alternatively, the friction drive wheel return spring might be broken or missing, requiring replacement and cable adjustment.
Z
zhutchinsonSep 7, 2025
Why does the drive speed control on my Power smart PSSAM24BS only work in one direction?
- A
  Ann WilliamsSep 7, 2025
  If your Power smart Snow Blower drive speed control only allows movement in one direction, inspect the speed control lever and cables for damage, looseness, or missing parts and repair or replace them as needed. Adjust the drive speed control cables.
R
Richard BrooksSep 10, 2025
Why is the auger rotating when auger control handle released on my Power smart PSSAM24BS?
- J
  Janet JohnsonSep 10, 2025
  If the auger on your Power smart Snow Blower rotates when the auger control handle is released, it is likely due to a broken or missing auger tension pulley arm return spring, which will need to be replaced.
P
paulgloverNov 13, 2025
What to do if my Power smart Snow Blower engine fails to start, but it cranks?
- B
  Brandon WarrenNov 14, 2025
  If your Power smart Snow Blower engine fails to start but cranks over, several issues could be the cause. First, ensure the spark plug wire is connected. A faulty spark plug can also prevent starting, so clean, adjust the gap, or replace it. If the engine is flooded with fuel, discontinue using the choke or primer and clean or replace the spark plug. Make sure the safety key is fully inserted into the ignition switch. Ensure the choke is in the START position, then slowly move it to the RUN position as the engine stabilizes. If it still doesn't start, try half choke. Old or stale fuel will not ignite, so empty and clean the fuel tank and carburetor and refill with fresh gasoline. A blocked fuel system or line should be cleaned. Lastly, ensure the extension cord is properly attached to the ...

Summary

Product Identification and Support

Model Number Identification

Identifies the specific PowerSmart snow thrower models covered.

Customer Support Contact Information

Provides phone number and website for customer assistance and inquiries.

Technical Specifications

PSSAM24 BS Technical Specifications

Details specifications for the PSSAM24BS model.

PSS2260 BS Technical Specifications

Details specifications for the PSS2260BS model.

Introduction

Manual Purpose and Scope

Explains the manual contains safety, operation, and servicing information.

General Safety Warnings and Precautions

Highlights safety instructions, potential hazards, and personal injury risks.

Customer Service Contact Details

Provides contact details for questions and resolving issues efficiently.

Training and Operation Guidelines

Operator Training Requirements

Emphasizes understanding instructions, controls, and safe practices.

Preparation for Operation

Details area inspection, safety gear, clothing, and surface preparation.

Personal Safety Guidelines

Covers exhaust risks, awareness, fatigue, and unattended operation.

Safe Gasoline Handling Procedures

Gasoline Handling Precautions and Safety

Lists safety rules for handling, storing, and refueling gasoline.

Safe Operation Practices and Warnings

Details safe operating procedures, avoiding contact with moving parts, and environmental awareness.

Maintenance and Storage Guidelines

Safety Device Maintenance

Advises regular checks of safety devices for proper operation.

Lubrication and Belt Checks

Covers gearbox lubrication and checking drive/auger control levers and cables.

Storage and Winterization

Provides guidance on preparing the unit for storage to prevent damage.

Cleaning and Unit Care

Cleaning Instructions

Details using a damp cloth and avoiding water in mechanisms.

Engine Modification Prohibition

Warns against modifying the engine, especially governor settings.

Snow Thrower Component Overview

Introduces component identification using illustrations.

Component Identification and Control Operation

Snow Thrower Component Reference

Lists and numbers various components of the snow thrower.

Control Lever Functions

Explains the function of drive control, speed control, and auger control levers.

Skid Shoe Adjustment Guide

Describes how to adjust skid shoes based on surface conditions.

Snow Thrower Pre-Operation Setup

Engine Oil: Recommendations and Filling

Provides oil type recommendations and instructions for checking and adding oil.

Gasoline: Adding and Capacity

Instructs on how to add gasoline, including capacity for different models.

Pre-Operation Checks and Snow Throwing

Gasoline Handling and Storage Tips

Provides important notes on gasoline usage, mixture, and storage.

Pre-Operation Inspection Checklist

Lists essential checks before using the snow thrower for the first time.

Auger and Drive Control Engagement

Explains how to engage the auger and drive systems.

Operating Your Snow Thrower Guide

Manual Engine Start Procedure

Step-by-step instructions for manually starting the engine.

Drive Speed and Direction Control

Explains how to set the drive speed and direction.

Chute Discharge Direction Adjustment

Details how to adjust the direction of snow discharge.

Snow Clearing and Shutdown Procedures

Electric Engine Start Procedure

Instructions for starting the engine using the electric start system.

Snow Clearing Operation Steps

Guides on engaging augers, setting speed, and directing the thrower.

Snow Thrower Shutdown Procedure

Steps for safely shutting down the engine and machine.

Maintenance Procedures

Tire Inflation and Maintenance

Specifies tire pressure and warnings against over-inflation.

Auger;Impeller Jam Clearing

Instructions for safely clearing auger or impeller jams.

Auger Shear Pin Replacement Guide

Explains the function of shear pins and how to replace them.

Troubleshooting Common Issues

Engine Start Troubleshooting

Addresses problems with the engine failing to start or cranking.

Electric Starter System Troubleshooting

Covers issues related to the electric starter not working.

Engine Performance Troubleshooting

Addresses engine running erratically, stalling, or low power.

Drive and Auger System Troubleshooting

Drive System Troubleshooting

Details issues with drive speed control and engagement.

Auger System Troubleshooting

Covers auger not rotating, poor performance, and belt issues.

Exploded View: Panel Assembly Parts

Panel Assembly Component List

Lists parts for the panel assembly with item numbers and descriptions.

Chute Assembly Details

Chute Assembly Component List

Lists parts for the chute assembly with item numbers and descriptions.

Frame Assembly: PSSAM24 BS Parts

PSSAM24 BS Frame Component List

Lists parts for the frame assembly of the PSSAM24BS model.

Frame Assembly: PSS2260 BS Parts

PSS2260 BS Frame Component List

Lists parts for the frame assembly of the PSS2260BS model.

Comprehensive Parts Breakdown

Model-Specific Part Identification

Lists detailed parts for both PSSAM24BS and PSS2260BS models.

Auger Housing Assembly Details

Auger Housing Assembly Component List

Lists parts for the auger housing assembly with item numbers and descriptions.

Auger Housing Assembly Component Details

Auger Housing Component Reference

Lists detailed parts for the auger housing assembly.

Two-Year Limited Warranty Information

Warranty Coverage and Exclusions

Outlines the warranty period, coverage, and exclusions for home use.

Implied Warranties and Damage Limitations

Discusses limitations on implied warranties and consequential damages.

Warranty Claims Process and Support

Provides instructions for making a warranty claim and contact details.