Powermate Vx - User Manual

16 pages

Save Page as PDF

To Next Page

Air Body Saw Instruction Manual

Mode d’emploi de scie pneumatique pour carrosserie

Modo de empleo de sierra neumática para carrocería

200-2973 , Rev. C, 7/25/18

Read and understand all safety precautions in this manual before operating. Failure to

comply with instructions in this manual could result in personal injury, property damage and/or voiding of

your warranty. The manufacturer WILL NOT be liable for any damage because of failure to follow these

instructions.

Lisez et veillez à bien comprendre toutes les consignes de sécurité de ce

manuel avant d’utiliser l’appareil. Toute dérogation aux instructions contenues dans ce manuel peut

entraîner l’annulation de la garantie, causer des blessures et/ou des dégâts matériels. Le fabricant NE

SAURA être tenu responsable de dommages résultant de l’inobservation de ces instructions.

Lea y comprenda todas las precauciones de seguridad contenidas en este

manual antes de utilizar esta unidad. Si no cumple con las instrucciones de este manual podría ocasionar

lesiones personales, daños a la propiedad y/o la anulación de su garantía. El fabricante NO SERÁ

responsable de ningún daño por no acatar estas instrucciones.

Model No.

024-0294CT

Max cutting thickness up to 16 gauge

Strokes per Minute 9,000-10,000

Maximum Working Pressure 90 PSI

Air requirements 2.6 CFM @ 90 PSI

Air Inlet 1/4” NPT (female)

Recommended hose size 3/8”

Blades (sold separately)

Item 024-0298CT (Course

Blade 24T)

Item 024-0300CT (Fine

Blade, 32T)

TOOL SPECIFICATIONS

Épaisseur de coupe maximale Jusqu’à un calibre de 16

Coups par minute 9000 -10000

Pression d’utilisation 90 lb/po² (6,2 bars)

Quantité d’air nécessaire 0,07 m3/min à 620 kPa

Admission d’air 1/4” po NPT

Taille de tuyau flexible recom-

mandée

10 mm (3/8 po)

Lames (vendues séparément)

Art. 024-0298CT (lame gros-

sière, 24T)

Art. 024-0300CT (lame ne,

32T)

CARACTÉRISTIQUES DE L’OUTIL

Grosor máximo de corte Hasta calibre 16

Golpes por minuto 9000 -10000

Presión operativa 90 PSI (6.2 bar)

Requerimientos de aire 0,07 m3/min à 620 kPa

Entrada de aire 1/4” NPT

Tamaño recomendado de

manguera

3/8”

Cuchillas (se venden por

separado)

Artículo 024-0298CT

(Cuchilla de trayectoria 24T)

Artículo 024-0300CT

(Cuchilla na, 32T)

ESPECIFICACIONES DE LA HERRAMIENTA

Main Page

Questions and Answers

A
Austin VaughnJul 29, 2025
Why does my Powermate Vx run slowly?
- A
  anna46Jul 29, 2025
  Your Powermate Saw might be running slowly due to several reasons. It could be due to grit or gumming up inside the tool. In this case, clean the air motor inside the tool with WD-40®. Also, ensure that there is enough oil in the tool by adding 4-6 drops of air tool oil into the air inlet. Check that the air pressure is adequate by adjusting the compressor regulator to 90 PSI. Finally, inspect the air hose for leaks and tighten the hose fittings with Teflon® tape if any leaks are found. Avoid excessive couplings between hoses, as pressure drops may occur.
B
Brad GuerraAug 11, 2025
What to do if my Powermate Saw will not run?
- V
  Vanessa EspinozaAug 11, 2025
  If your Powermate Saw won't run, there are a few potential causes. First, the air motor inside the tool may need cleaning with WD-40® due to grit or gumming. Another possibility is that the tool needs oil; add 4-6 drops of air tool oil into the air inlet. Verify that the compressor regulator is set to 90 PSI to ensure adequate air pressure. Check for air hose leaks and tighten any leaking fittings with Teflon® tape. Additionally, minimize the use of excessive couplings between hoses to prevent pressure drops.