PowerTec 3000C - 2.0 SPECIFICATIONS; 6.3 CURRENT SENSOR BOARD

© copyright 1992, 1996 by Powertec Industrial
Motors
Page 9
2.0 SPECIFICATIONS
2.1 ELECTRICAL RATINGS
LINE APPROX MAXIMUM MAXIMUM MAXIMUM TRIP * HP ** HALL
VOLTS LINE MOTOR HEAT HEAT CALIBRATE CALIBRATE SENSOR
VAC HORSE KILO CURRENT CURRENT OUTPUT IN RESISTOR RESISTOR STYLE
POWER WATTS AAC RMS AAC RMS WATTS BTU/HR OHMS OHMS CSLA1
Model 2000C
230 15 11 36 64 575 1962 OPEN 4.64 K CH
230 20 15 47 83 720 2457 15 K 7.15 K DK
380 15 11 19 36 545 1860 15 K 8.25 K CH
380 20 15 25 50 690 2355 13 K 5.90 K CH
380 25 18 31 60 812 2771 OPEN 4.99 K CH
380 30 22 38 72 935 3191 15 K 8.25 K DK
460 15 11 18 31 475 1631 10 K 6.19 K CH
460 20 15 23 42 650 2218 20 K 7.15 K CH
460 25 18 28 53 785 2670 39 K 5.62 K CH
460 30 22 34 63 903 3082 OPEN 4.75 K CH
460 40 30 45 82 1125 3840 15 K 7.15 K DK
Model 3000C
230 25 18 57 102 841 2870 20 K 5.90 K DK
230 30 22 68 121 993 3389 62 K 4.87 K DK
380 40 30 50 96 1186 4037 20 K 6.19 K DK
380 50 37 63 120 1254 4280 62 K 4.87 K DK
380 60 45 75 144 1301 4440 OPEN 4.12 K DK
460 50 37 55 96 1190 4061 20 K 6.19 K DK
460 60 45 66 120 1267 4325 62 K 4.87 K DK
460 75 56 81 149 1499 5116 OPEN 4.12 K DK
* Trip resistor is on Current Sensor board TB3 terminals 1 and 2; OPEN means no resistor is needed. All resistors are 1/4 watt, 1%.
** HP calibration resistor is on Current Sensor board TB3 terminals 4 and 5; All resistors are 1/4 watt, 1% tolerance.
Hall Sensor style refers to part number of Hall Effect Current Sensors. The number is on the sensor.
2.2 DIMENSIONS
Model 2000C chassis: 19.50"H x 13.75"W x 13.38"D (495mmH x 350mmW x 340mmD) Weight = 94 lbs (43 Kg)
Model 3000C chassis 25.25"H x 13.75"W x 13.38"D (641mmH x 350mmW x 340mmD) Weight = 115 lbs (52 Kg)
Model 2000C NEMA 1: 35.8"H x 24.4""W x 17.0"D (908mmH x 620mmW x 432mmD) Weight = 130 lbs (59 Kg)
Model 3000C NEMA 1: 50.8"H x 24.4"W x 17.0"D (1290mmH x 620mmW x 432mmD) Weight = 160 lbs (73 Kg)
Standard dimensions and weights do not include options.
2.3 ENVIRONMENTAL
ALTITUDE: Use above 3300 ft (1000 m) requires derating
AMBIENT TEMPERATURE:
Chassis 55°C (131°F) maximum
NEMA 1 40°C (104°F) maximum
INPUT VOLTAGE TOLERANCE: +10%, -5% at all times
INPUT POWER FREQUENCY: 48 to 62 Hertz
RELATIVE HUMIDITY: 95% (non-condensing)
SERVICE FACTOR: 1.0
MAXIMUM SERVICE CAPACITY: 100 KVA (limited by input fuses AIC rating)
STORAGE TEMPERATURE: -40°C to +65°C