EasyManuals Logo

Precor Spinner Chrono Assembly Guide

Precor Spinner Chrono
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Spinner® Chrono™ Power and Spinner® Climb™ Bike Assembly Guide
To assemble your equipment, follow the steps in the order listed in this assembly guide. For
more product information, visit us at www.precor.com.
CAUTION
At least two people are required to assemble the equipment. DO NOT
attempt assembly by yourself.
Seat assembly
Handlebar
assembly
Rear
stabilizer
Bike frame
Seat post
Handlebar post
Front
stabilizer
Pedal
Seat adjustment
pop-pin
Handlebar
adjustment
pop-pin
Seat
slider knob
Fore/aft handlebar
knob
Resistance
knob
Flywheel
Adjustment feet
Crank arm
Assembly requirements
When assembling the bike, we recommend you:
Unpack the box and assemble the equipment close to where you plan to use it.
Assemble and operate the equipment on a solid, level surface.
Leave a minimum of 0.5 m (19.7 in.) on at least one side of the bike and 0.5 m (19.7 in.)
behind or in front of the bike.
Hardware kit
Component Quantity Component Quantity
Socket head bolt (M8 x 30 mm) 4 Hex key (8 mm) 1
Flat washer (8 mm) 4 Hex key (2.5 mm) 1
Socket head bolt (M3 x 8 mm) 6 Seat slider end cap 1
Socket head bolt (M8 x 16 mm) 2 Handlebar post end cap 1
Hex key (6 mm) 1 Stabilizer attachment bar 2
Begin Assembly
Remove the following parts from the packaging: handlebar assembly, handlebar post, hardware kit, product documentation, seat assembly, seat post,
and spare parts.
CAUTION
Damage to the bike during assembly is not covered by the Precor Limited Warranty.
During assembly, you must protect the handlebar and seat adjustment pop-pin threaded stems from damage.
To attach the rear stabilizer:
1. Stand the bike frame on its front end (toward ywheel) and place a piece of packaging foam under the bike
frame (Figure 1) to protect the handlebar adjustment pop-pin stem from damage.
2. Remove the packaging from the rear stabilizer and gently pry off the plastic protection plate from the
frame. Be careful not to chip the paint.
3. Slide the rear stabilizer attachment bar into the slot in the bike frame (Figure 2).
4. Attach the rear stabilizer to the frame using two bolts two at washers (Figure 3).
Using a hex key
, tighten to 15.6 ft-lb (21.2 N-m).
To attach the front stabilizer:
1. Stand the bike frame on its back end and place a piece of packaging foam under the bike frame (Figure 4) to
protect the seat adjustment pop-pin stem from damage.
2. Remove the packaging from the front stabilizer and gently pry off the plastic protection plate from the
frame. Be careful not to chip the paint.
3. Slide the front stabilizer attachment bar into the slot in the bike frame (Figure 2).
4. Attach the front stabilizer to the frame using two bolts
and two at washers (Figure 5).
Using a hex key , tighten to 15.6 ft-lb (21.2 N-m).
5. Return the bike to the upright position.
Figure 1
Figure 4
Figure 2
Figure 3
Figure 5

Other manuals for Precor Spinner Chrono

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Precor Spinner Chrono and is the answer not in the manual?

Precor Spinner Chrono Specifications

General IconGeneral
BrandPrecor
ModelSpinner Chrono
CategoryFitness Electronics
LanguageEnglish

Related product manuals