EasyManua.ls Logo

Predator 63404 - Pre-Start Checks; Priming the Pump; Checking and Filling Engine Oil

Predator 63404
24 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Page 10 F*+&<(=:$#='B&T;("<#*$"E&@B('"(&='BB&NOPPPOPRROUVSV8 ITEM 63404
7-F652 3[6D-503. 4-0.56.-.,6765![
3@(+'<#*$&
D(')&<:(&6.50D6&04[3D5-.5&7-F652&0.F3D4-503.&"(=<#*$&'<&<:(&>(%#$$#$%&*I&<:#"&?'$;'B&
#$=B;)#$%&'BB&<(9<&;$)(+&";>:(')#$%"&<:(+(#$&>(I*+(&"(<&;@&*+&;"(&*I&<:#"&@+*);=<8
[+(O7<'+<&,:(=d"
Inspect engine and equipment looking for damaged, loose, and missing parts before set up
and starting. If any problems are found, do not use equipment until fixed properly.
[+#?(&<:(&[;?@
Before starting the engine, fill the Pump with water.
To do this:
1. Unthread the Priming Water Filler Cap
by turning it counterclockwise.
2. Fill the unit with clean water up to the
top of the opening. Replace the Priming
Water Filler Cap and tighten securely.
04[3D5-.5^ Always check for water in the Pump
Housing before each use. Never attempt to run the
Water Pump without the Pump Housing FULL of water.
D;$$#$%&<:(&\'<(+&[;?@&G#<:*;<&G'<(+&I*+&
'$&(9<($)()&@(+#*)&*I&<#?(&G#BB&)'?'%(&<:(&
\'<(+&[;?@&'$)&J*#)&<:(&\'++'$<A8
[+#?#$%&,'@
,:(=d#$%&'$)&F#BB#$%&6$%#$(&3#B
.350,6K&&2*;+&\'++'$<A&#"&C30H&#I&<:(&($%#$(j"&
=+'$d='"(&#"&$*<&@+*@(+BA&I#BB()&G#<:&*#B&>(I*+(&
('=:&;"(8&&](I*+(&('=:&;"(E&=:(=d&<:(&*#B&B(J(B8
Engine&G#BB&$*<&"<'+<&G#<:&B*G&*+&$*&($%#$(&*#B8
3. Make sure the engine is stopped and is level.
4. Close the Fuel Valve.
5. Clean the top of the Dipstick and the area around it.
Remove the Dipstick by turning it counterclockwise,
and wipe it off with a clean, lint free rag.
6.
Full level
Full level
Reinsert the Dipstick without threading it in and
remove it to check the oil level. The oil level
should be up to the full level as shown above.
7. If the oil level is at or below the low mark add the
appropriate type of oil until the oil level is at the
proper level. SAE 10W-30 oil is recommended for
general use. (The SAE Viscosity Grade chart on
page 15 in the Maintenance section shows other
viscosities to use in different average temperatures.)
8. Thread the dipstick back in clockwise.
.350,6K&&H*&$*<&+;$&<:(&($%#$(&G#<:&<**&B#<<B(&*#B8
Engine&G#BB&":;<&*II&#I&($%#$(&*#B&B(J(B&#"&<**&B*G8

Related product manuals