Pro Mach ORION Sentry HP

Questions and Answers

L
Luis RollinsAug 3, 2025
Why won't my Pro Mach ORION Sentry HP Stretch Wrapping Systems machine start?
- L
  Laura NewmanAug 3, 2025
  Your Pro Mach Stretch Wrapping Systems machine might not start because: * The E-stop button is pressed. If this is the case, release the E-stop button. * The carriage obstacle detect switch or carriage door open switch located on the bottom of the carriage is pressed. Ensure the bottom of the carriage isn't pressing on any obstructions and that the carriage door is closed. * The machine isn't plugged in or the power switch is off. Plug in the machine and turn the Power On/Off Switch to the On position.
A
Amanda LarsenAug 8, 2025
What to do if my Pro Mach Stretch Wrapping Systems turntable will not turn?
- S
  spencervictoriaAug 8, 2025
  If the turntable on your Pro Mach Stretch Wrapping Systems machine isn't turning, it could be due to a couple of reasons: * The turntable speed is set too low. Adjust the turntable speed on the HMI. * The carriage obstacle detect switch or carriage door open switch located on the bottom of the carriage is pressed. Make sure that the bottom of the carriage isn't pressing on any obstructions and the carriage door is closed.
D
Debra WiseAug 13, 2025
Why is my Pro Mach ORION Sentry HP film constantly breaking?
- C
  Cody LawrenceAug 13, 2025
  Continual film breakage in Pro Mach Stretch Wrapping Systems can occur due to: * Film tension being set too high. Decrease the film tension on the HMI. * Using bad or old film. Replace the film spool.
S
Scott AvilaAug 18, 2025
What to do if the Pro Mach ORION Sentry HP machine cycle stops?
- J
  Jose CortezAug 18, 2025
  If the Pro Mach Stretch Wrapping Systems machine cycle stops, it is likely that the obstruction switch on the bottom of the film carriage was tripped. Remove the obstruction and restart the program.
N
Nicole HartAug 23, 2025
Why won't the carriage on my Pro Mach ORION Sentry HP Stretch Wrapping Systems raise or lower?
- J
  Joyce NicholsAug 23, 2025
  If the carriage on your Pro Mach Stretch Wrapping Systems isn't raising or lowering, consider these possibilities: * The carriage speed is set too low. Adjust the carriage speed on the HMI. * The carriage obstacle detect switch or carriage door open switch located on the bottom of the carriage is pressed. Ensure that the bottom of the carriage isn't pressing on any obstructions and the carriage door is closed.
R
Rebecca SimmonsAug 28, 2025
What causes the carriage to go too far past the top of the load on Pro Mach ORION Sentry HP?
- A
  Alyssa MontoyaAug 28, 2025
  If the carriage continues too far past the top of the load on your Pro Mach Stretch Wrapping Systems, it means that the photocell delay setting found on the Top Wraps Modification Screen is set too high. Decrease the photocell delay.

Summary

Introduction and Safety

Safety Guidelines

General safety guidelines for operating and maintaining the equipment.

System Safety Recommendations

Specific safety precautions for system operation and maintenance.

Lockout and Tagout Recommendations

Procedures for electrical system lockout/tagout.

Installation and First Time Power Up

Steps for initial machine setup and power connection.

System Description

Machine Specifications

Details the technical specifications of the Sentry HP/LP machines.

Control Features

Lists the control system features and interface.

Structural Features

Outlines the physical construction and build of the machine.

System Operation

Operating Procedures

General procedures for operating the stretch wrapper.

How to Start and Shut Down Your Wrapping System

Step-by-step guide for starting and stopping the machine.

Run Screens

Overview of the machine's primary operational screen.

Machine Settings Screens

Access point for various machine configuration settings.

Diagnostics Screens

Interface for system diagnostics and status checks.

Troubleshooting

Troubleshooting Guide

Guide to diagnosing and resolving machine problems.

Maintenance

General Maintenance

General information on maintaining the stretch wrapper.

Preventative Maintenance Schedule

Recommended maintenance intervals and tasks.

Reducer Oil Change

Steps and lubricant recommendations for changing transmission oil.

Electrical and Mechanical Drawings

Electrical Prints

References to electrical schematics for the machine.

Mechanical Drawings

References to mechanical diagrams of the machine.

Pro Mach ORION Sentry HP Specifications

General

Manufacturer	Pro Mach
Model	ORION Sentry HP
Type	Stretch Wrapping System
Brand	ORION
Turntable Diameter	60 inches
Film Width	20 inches
Machine Type	Turntable
Load Height	Up to 80 inches (2032 mm)
Load Weight	Up to 4, 000 lbs
Cycle Time	Up to 30 cycles per hour
Control System	PLC
Film Delivery	Powered pre-stretch
Power Requirements	208-240 VAC, 3 Phase, 60 Hz