EasyManua.ls Logo

PT M503 - User Manual

Default Icon
8 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
LIMITED WARRANTY
PERFORMANCE TOOL® extends only the following warranties, and only to original retail purchasers. These warranties give specific legal rights. Except
where prohibited by local law, the law of the State of Washington governs all warranties and all exclusions and limitations of warranties and remedies.
There may be other rights which vary from state to state.
PERFORMANCE TOOL® warrants the product to be free from defects in materials and workmanship under normal use and service. A defective product
may be returned for a free replacement within 90 days from the date of purchase, provided that product is returned to place of purchase immediately after
discovery of defect. After 90 days and up to one year from date of purchase, PERFORMANCE TOOL® will replace at no charge any parts which our
examination shall disclose to be defective and under warranty. These warranties shall be valid only when a sales receipt showing the date of purchase
accompanies the defective product or defective part (s) being returned. For part (s) after 90 days, please remit your request, postage prepaid to:
PERFORMANCE TOOL, P.O. Box 88259 Tukwila, WA 98138
These warranties exclude blades, bits, punches, dies, bulbs, fuses, hoses, and other consumables which must be replaced under normal use and service.
These warranties shall not apply to any product or part which is used for a purpose for which it is not designed, or which has been repaired or altered in
any way so as to affect adversely its
performance or reliability, nor shall these warranties apply to any product or part which has been subject to misuse, neglect, accident or wear and tear
incident to normal use and service.
PERFORMANCE TOOL® does not authorize any other person to make any warranty or to assume any liability in connection with its products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL® makes no express or implied warranties of any
kind with respect to its products. In particular, PERFORMANCE TOOL® makes no implied warranty of merchantability and no implied warranty of fitness for
any particular purpose, except that for goods purchased primarily for personal, family or household use and not for commercial or business use,
PERFORMANCE TOOL® makes an implied warranty of merchantability (and, if otherwise applicable, an implied warranty of fitness for a particular
purpose), but only for the particular qualities or characteristics, and for the duration, expressly warranted above.
The laws on limitation of implied warranties may differ from state to state, so the above limitations may not apply in all cases.
PERFORMANCE TOOL® shall not be liable for consequential, incidental or special damages resulting from or in any manner related to any product, or to the
design, use, or any inability to use the product. The sole and exclusive remedy for a defective product or part shall be the repair, or replacement thereof as
provided above. The laws on limitation of remedies or on consequential, incidental or special damages may vary from state to state, so the above
limitations may not apply in all cases.
© Copyright 2014 WILMAR CORPORATION, P.O. Box 88259 Tukwila, WA 98138

Questions and Answers

  • J
    Jason TuckerJul 28, 2025
    What to do if my PT M503 Paint Sprayer is spitting?
    • J
      Jeffery BarnesJul 29, 2025
      If your PT Paint Sprayer is spitting, several factors could be the cause. First, check the material level in the cup and refill if it's too low. A loose fluid nozzle can also cause spitting, so ensure it's properly tightened. Inspect the needle packing for damage and replace if necessary. Lastly, a dirty or damaged needle and nozzle set might be the culprit; try cleaning or replacing these parts.
  • A
    adam27Aug 5, 2025
    Why does my PT M503 Paint Sprayer have an irregular spray pattern?
    • M
      Mariah MccallAug 5, 2025
      An irregular or offset pattern from your PT Paint Sprayer can stem from a dirty or damaged needle tip or fluid nozzle; in this case, clean or replace the needle or fluid nozzle. It may also be caused by clogged atomization holes on the air nozzle around the center, so try cleaning the air nozzle.
  • C
    Christopher MacdonaldAug 13, 2025
    Why is the material in the cup of my PT M503 bubbling?
    • S
      Steven BlevinsAug 13, 2025
      If the material in the cup of your PT Paint Sprayer is bubbling or "boiling", it could be due to a loose, clogged, or damaged fluid nozzle, so clean, tighten, or replace it. Alternatively, a loose, clogged, or damaged air nozzle might be the cause; in that case, clean, tighten, or replace the air nozzle.
  • M
    Melissa FritzAug 20, 2025
    How to fix a half-moon shaped spray pattern with my PT M503?
    • T
      Tyler BrownAug 20, 2025
      A half-moon shaped pattern from your PT Paint Sprayer is often caused by clogged air holes on the air nozzle ears. To resolve this, carefully clean out the holes with wire after soaking in thinner.

Summary

Limited Warranty

Specifications

Troubleshooting

1.5 mm HVLP Spray Gun Parts List

Important Safety Information

Care and Maintenance

Operation

Inlet Air Pressure Regulation

Regulates air pressure for optimal spray gun performance by adjusting the pressure regulator control knob.

Air and Fluid Volume Controls

Adjusts air and fluid flow to accurately set the air/fluid ratio for paint application.

Spray Pattern Controls

Adjusts spray pattern shape and orientation by manipulating the pattern control knob and air nozzle.

1.2 mm HVLP Spray Gun Parts List

PT M503 Specifications

General IconGeneral
BrandPT
ModelM503
CategoryPaint Sprayer
LanguageEnglish

Related product manuals