Pulsar CZ6-100C - User Manual

Mains Supply ChromaZone(s)
mains cable
WARNING - THIS APPLIANCE MUST BE EARTHED
For safety we recommend the use of a Residual Current
Circuit Breaker. An RCCB MUST be used when powering
e.g. ChromaFixtures in wet environments.
Electronics On/Off Switch Indicator Neon
Electronics Mains Fuse
- The works correctly on any
mains voltage from 85-277 VAC, 50-60Hz, (self adjusting).
Power consumption: CZ6 - 100 Watts, CZ12 - 200 Watts
depending on the number of fixtures connected and their output
levels. Please see the table shown below for more information.
A with locking IEC female connector attached is
supplied (not supplied with IP Zones). To unlock the IEC
connector, pull/side the red tab towards yourself then pull
connector out. The other end of the cable should be fitted with a
suitably approved and rated mains plug. Note: in some countries
it is a requirement that such a plug be fitted by a qualified
electrician.
with built in .
: 5 Amp, HRC, 5x20mm.
Pulsar's Chroma Lighting Fixtures - ChromaStrips ,
ChromaTubes , ChromaPanels , CAR111
ChromaScapes , CBAT17 , ChromaBatten50 ,
ChromaHearts , ChromaInGround , ChromaFlood50 ,
ChromaPoint , ChromaInGroundMR16SS , etc
ChromaFixtures Leaflet
ChromaZone Max Fixture
Loading Data
ChromaZone ,
(User Interface Module)
DMX D M X
CZ6/12
.
TM
TM TM TM
TM TM TM
TM TM TM
TM TM
TM
., contain
state of the art, high brightness, high efficiency Red, Green and
Blue LEDs. These three primary colours can be mixed together
to make an incredible pallet of 16.7 million colours.
Please see the for details of the
luminaires themselves and page 3 -
which will inform you of how many fixtures you may
put on the outputs of different ChromaZones.
The has numerous chases and effects built in
making it possible to achieve fantastic effects without
programming. These internal effects can be selected via the UIM
on the lid of the unit in Stand Alone
mode or from a controller using a digital ( igital ultiple )
signal.
When receiving a signal the can operate in 3, 6, 9, 10, 36,
42 or 46 Channel Modes Please see the lid printing page for
details of these Operating Modes, how to select them, Channel
Listings, and further information.
Each ChromaFixture requires a +24VDC supply and three 0 to
+10V control signals to control the level of Red, Green and Blue.
These control signals and the low voltage power are provided by
the CZ12 and CZ6 controllers which can drive up to 12 or 6
ChromaFixtures respectively.
ChromaZone12 200W - Mk2
TM
CZ12-200
ChromaZone6 100W - Compact
TM
CZ6-100C
ChromaPSU2 PSU
TM
CPSU2
Cable Colours
Green/Yellow =
Brown =
Blue =
Earth / Ground
Live / Phase / Hot
Neutral
ChromaFlex Grey 5 Core Multiway Cable
8075G
8075SUB
ChromaFlex Submersible 5 Core Cable
CZ12-200IP ChromaZone12 200W - IP65
TM
Model
Outputs
Max Load Control
50W
17W CP300
MR16
Link
Point
Strip 25/X1 Strip X3
CZ12-200(IP)
12
200W
DMX
4
12
48 60 96
96
14.4 mts 4.8 mts
CZ6-100C 6 100W
DMX
2
6
24
30 48
48
7.2 mts 2.4 mts
CPSU2
2
35W 0-10V 0
2
81016
16
2.4 mts 0.6 mts
The CBAT50, CFLD50 and CIG50 require up to 50 Mains Watts
each which will reduce the number of products you can use per
ChromaZone e.g. 4 x CFLD50 = 200W. Do not exceed the max
mains wattage of the zone.
NB - Patents applied for. Trade Marks, Copyright, Registered
and Unregistered Design Rights apply on all Chroma
Products.
CHROMA CHROMARANGE ZONE
CHROMAZONE MAINS SUPPLY
GENERAL INFORMATION
Pulsar Light of Cambridge Limited Tel: Email: Web:, 3 Coldhams Business Park, Cambridge, CB1 3LH, England 44 (0)1223 403500 sales@pulsarlight.com www.pulsarlight.com
7571 PSU12-200IP Instructions

Summary

ChromaZone Mains Supply and Safety

Appliance Earthing Warning

Safety warning emphasizing the need for earthing the appliance, especially in wet environments, recommending an RCCB.

CZ6 & CZ12 Signals and Connections

DMX In;Thru 5 Pin XLR Connectors

Details pin connections for DMX input/output using 5-pin XLR connectors, including signal and cable colours.

4 PIN XLR Low Voltage and DMX Output

Describes the 4-pin XLR output for 24VDC power and DMX, and its pin connections.

CZ6 & CZ12 Mounting and Fuses

Unit Mounting Options

Internal Fuse and Protection

User Interface Module (UIM) Functions

DMX Address and Mode Settings

Procedure for setting the DMX start address and selecting the ChromaZone operating mode.

UIM Advanced Settings and Standalone Mode

DMX Line Termination and No Signal Handling

Instructions for DMX line termination and configuring behavior when no DMX signal is received.

Standalone Settings View;Change

Procedure for viewing, changing, and saving standalone settings based on signal presence.

UIM Menu Selection Overview

DMX Address and ChromaZone Mode

Overview of menu options for setting DMX address and ChromaZone operating mode.

Standalone Mode and Factory Reset

Options for 'If NoSignal use', Stand Alone Settings, and restoring factory default settings.

Important Safety Instructions

General Safety Precautions

Instructions for reading leaflets, observing warnings, and protecting the power cord.

Usage and Servicing Guidelines

Guidelines on using specified attachments, servicing, cleaning, and avoiding liquids.

Environmental and Electrical Safety

Warnings against use near water, blocking ventilation, and defeating safety plug features.

Pulsar CZ6-100C Specifications

General

Brand	Pulsar
Model	CZ6-100C
Category	Lighting Equipment
Language	English