To Next PageTo Next Page
Need help?Do you have a question about the Pulsar CHROMA Series and is the answer not in the manual?
General| Brand | Pulsar |
|---|---|
| Model | CHROMA Series |
| Category | Lighting Equipment |
| Language | English |
Lists various ChromaZone models and their specifications including power and type.
Explains how ChromaFixtures use +24VDC supply and 0-10V control signals for R, G, B levels.
Details internal chases, effects, and DMX/standalone operating modes for CZ6/12.
Warns against exceeding maximum mains wattage per zone when using specific Pulsar products.
Specifies the wide AC input voltage range and power consumption of CZ6 and CZ12 units.
Describes how to connect the supplied IEC mains cable, including unlocking and fitting the plug.
Highlights the requirement for earthing, use of RCCB in wet environments, and mains fuse rating.
Details the pin configuration for DMX input/output using 5-pin XLR connectors.
Explains the 4-pin XLR output for LVS and DMX, and its use for powering additional units.
Describes the 5-pole Wago connectors for ChromaFixture outputs, providing power and signal.
Provides instructions on stripping and connecting ChromaFlex cable to cage clamp connectors.
Instructions for mounting the CZ6/12 using supplied brackets, including bracket adjustment.
Identifies the M6 hexsert for attaching a safety chain.
States that a blown 5 Amp fuse indicates an internal fault requiring professional service.
Explains the resettable fuse for 24VDC outputs and how to reset it after a fault.
Notes that 0-10V signal inputs/outputs are protected against shorts and static damage.
Details mains wiring via Wago connector and 5-pole Wago output blocks for IP rated units.
Shows the DMX connector wiring for the IP Zone, including DMX IN and DMX THRU.
Instructions for drilling, tapping, and installing M12 liquid tight glands for cable entry.
Describes the use of supplied mounting plates for wall or ceiling installation of the CZ12-200IP.
Identifies M10 nutserts on the underside and top for mounting the CZ12-200IP.
Details portable appliance testing capabilities, electrical safety, EMC, and IP ratings.
Explains CE/ETL markings, compliance directives, and the three-year guarantee terms.
Describes the 2-line LCD display, status indicators, and key functions for menu navigation.
Instructions for setting the DMX start address and selecting the ChromaZone operating mode via the UIM.
Guides on setting channels per fixture, fixture number, and chase patterns using the UIM.
Explains how to set Channel 10 as a Grand Master for RGB or Global Master via the UIM.
Details how to enable/disable input smoothing and DMX line termination for optimal signal integrity.
Covers enabling low voltage supply and configuring the unit's behavior when no DMX signal is received.
Describes how to view, change, and save Stand Alone settings for different signal conditions.
Details the UIM menu path for setting DMX address and ChromaZone operating mode.
Maps out the UIM navigation for fixture number, chase patterns, and Channel 10 functions.
Covers UIM options for input smoothing, LV supply, termination, no-signal use, and factory reset.
Introduces v4.0, highlighting built-in chases, master dimmer, and input smoothing flexibility.
Details the 7 operating modes and the role of the Master Dimmer Channel (Ch.10) as Global Grand Master.
Explains the chase select table, its chase numbers, input/bit values, descriptions, and notes.
Details channel assignments for 6-channel and 10-channel operating modes for ChromaZone units.
Provides channel mapping for 36-channel mode for both ChromaZone 6 and ChromaZone 12.
Lists channel assignments for 42-channel and 46-channel modes across ChromaZone 6 and 12.
Emphasizes reading leaflets, observing warnings, following instructions, and protecting the power cord.
Covers using specified mounting, referring servicing to qualified personnel, and cleaning procedures.
Details restrictions on use near water, blocking ventilation, and defeating safety plug features.
