Pulsar SiPPER User Manual

AUTO MODE
Alternatively, you can press the touchpad 2 times to start the
auto lling mode. The Sipper will run for 1 minute continuously.
Once you see the dry cup is full press the touchpad 1 time to
stop the auto mode. Depending on the cartridge your dry cup
may ll before the 1 minute is up.
Pro tip: This mode may be able to clear small clogs that could
occur in the cartridge or atomizer. If it takes more than 20
seconds, disable Auto Mode and use the included dab tool as
a poker to manually clear the clog.
CLEANING
Take apart the unit completely for cleaning. First, remove
airow valve and separate the two pieces. Next, remove the
atomizer/cartridge cover from the base of the unit and remove
the airow silicone. Lastly, remove the atomizer or cartridge
from the 510 connection, and unscrew 510 connection from
the base.
Glass: Wipe the inside of the dry cup with an alcohol wipe
until all the residue has been removed. Alternatively, you
could put the entire dry cup into 91% alcohol or glass cleaner
and wait till the residue is dissolved.
Silicone Parts, 510 Connection, Base: Use an alcohol wipe or a
cotton swab and 91% alcohol to clean off the build up on all of
the silicone parts and 510 connection. Use a cotton swab and
91% alcohol to clean any buildup beneath the 510 connection.
TROUBLESHOOTING
Dead Coil / No Connection: When the coil burns out or is not
making a proper connection the light will ash red 3 times.
Try removing and reinstalling the wax atomizer to reset
connection. Otherwise, replace with a new wax atomizer.
Low Battery Indicator: When the battery is less than 5% the
light will ash red 8 times and the Sipper will power off. Use
the USB-C charging cable to recharge the Sipper until the
touchpad light turns green.
For warranty servicing, contact us at PulsarShop.com.
IMPORTANT SAFETY WARNINGS
• Do not expose to extreme temperatures or direct sunlight for
prolonged periods.
• Do not drop the Sipper or accessories.
• Do not drop or submerge the base in any liquid.
• Do not modify the electronics in any way.
• This device is intended for adults only. Do not sell or provide to
minors. Keep all parts, concentrates, herbs, and liquids away
from children and pets. This is not a medical device and is not
intended to diagnose, treat, mitigate, cure, or prevent any ailment,
disease, or other conditions. Consult a physician before use,
especially if you suffer from heart disease or any other medical
condition, or if you are pregnant or breastfeeding. Failure to follow
any of these instructions could result in product damage, property
damage,personal injury, and may void warranty.
PU-0648-23
PULSARSHOP.COM
ASSEMBLY
Remove the atomizer/cartridge cover from the Sipper base
and screw the wax atomizer or cartridge (not included)
into the 510 connection then replace the cover. The light
around the touchpad will ash the current voltage to show
a successful connection has been made if the Sipper is
already on. Put the two pieces of the airow valve together
before inserting it into the bottom of the dry cup. Now place
the dry cup on top of the cover, lightly pressing down so
there is a good t. This should not require a lot of pressure.
LOADING
Remove the dry cup from the cover and then remove the
cover from the base. With the wax atomizer connected, load a
small amount of concentrate into the atomizer. About a half grain
of rice is all that is needed; be sure not to overll the atomizer.
Then replace the cover and sit the dry cup back on top.
ATTENTION! Do not touch the coils with metal dab tools
while the Sipper is working.
USAGE
• Power On/Off - Press the touchpad with the tip of your nger
5 times to turn on the Sipper, the light around the touchpad
will ash to let you know it is on and the battery life.
Green - 100% - 70% Blue - 70% - 30% Red - 30% - 0%
NOTE: The Sipper will automatically turn off after 10 minutes of inactivity.
• Operating Wax Atomizer - With the Sipper turned on, press
the touchpad 3 times to change your voltage. Once you
have your voltage selected, touch and hold the touchpad.
You will hear the pump activate and see the vapor start
lling the dry cup. Once the dry cup is lled, pull the dry
cup off the base, and inhale through the mouthpiece.
• Operating 510 Cartridge - Remove the wax atomizer and
unscrew the 510 connection before inserting a .5ml or 1ml
510 cartridge to the 510 connection, then screw the 510
connection back into the base. Replace the cover and sit
the dry cup back on top. Press the touchpad 5 times to
turn on the Sipper, the light around the touchpad will ash
to let you know it is on. Press the touchpad 3 times to select
your voltage. Once you have your voltage selected press
and hold the touchpad and you will hear the pump activate
and see the vapor start lling the dry cup. Once the dry
cup is lled, pull the dry cup off the base, and inhale
through the top.
NOTE: The Sipper works with most cartridges but not all cartridges.

Pulsar SiPPER Specifications

General

Brand	Pulsar
Model	SiPPER
Category	Vaporizers
Language	English