QCA Spas QCA Paradise Series

Questions and Answers

J
John ValenzuelaSep 10, 2025
Why does my QCA Spas Hot Tub display ----?
- J
  jennifercruzSep 10, 2025
  The display of ---- on your QCA Spas Hot Tub indicates that in Economy or Sleep mode, the pump may be off for hours outside a filter cycle. If you wish to see the current spa temperature, either switch to Standard mode or turn Jets1 on for at least two minutes.
S
Stephanie PotterAug 22, 2025
Why does my QCA Spas Hot Tub display SPA TEMP LMT?
- K
  Kevin OlsonAug 22, 2025
  The SPA TEMP LMT message on your QCA Spas Hot Tub means one of the sensors has detected that the spa water is 110°F (approximately 43.3°C). Do not enter the water. Remove the spa cover and allow the water to cool. The spa should automatically reset at 107°F (approximately 41.7°C). If it doesn't, shut off the power to the spa and call your dealer or service organization.
Z
zwilliamsonAug 25, 2025
What to do if my QCA Spas QCA Paradise says HTR FLOW LOW?
- D
  dunnpamelaAug 25, 2025
  If your QCA Spas Hot Tub displays the message HTR FLOW LOW, it means a substantial difference between the temperature sensors was detected, possibly indicating a flow problem. First, check the water level in the spa and refill if necessary. If the water level is adequate, ensure the pumps have been primed. If the problem persists, contact your dealer or service organization.
S
Stephanie HessAug 26, 2025
What does FREEZE COND mean on my QCA Spas QCA Paradise Hot Tub?
- S
  Shelley CarterAug 26, 2025
  The FREEZE COND message on your QCA Spas Hot Tub indicates freeze conditions. No action is required. The pumps and the blower will automatically activate regardless of spa status.
R
Robert ThomasAug 27, 2025
What does LOW FLOW mean on my QCA Spas QCA Paradise and what should I do?
- J
  Justin StrongAug 28, 2025
  The LOW FLOW message on your QCA Spas Hot Tub indicates persistent low flow problems, occurring after the “HTR FLOW LOW” message has appeared three times. Follow the actions required for the “HTR FLOW LOW” message. Turn the spa off and then back on again to restore heating capability.
I
imeyerAug 29, 2025
What to do if my QCA Spas QCA Paradise displays HEATER MAY BE DRY – WILL RESET SHORTLY?
- M
  melissaduffyAug 29, 2025
  If your QCA Spas Hot Tub displays the message HEATER MAY BE DRY – WILL RESET SHORTLY, it indicates inadequate water detected in the heater. Check the water level in the spa and refill if necessary. If the water level is okay, make sure the pumps have been primed. Press any button to reset.
C
Christine HudsonSep 18, 2025
What does NEW FILTER mean on my QCA Spas QCA Paradise?
- E
  Elizabeth GardnerSep 18, 2025
  The NEW FILTER message on your QCA Spas Hot Tub means that you should install a new filter.
P
Paul FlowersSep 12, 2025
What does CLEAN FILTER mean on my QCA Spas Hot Tub?
- J
  Joseph HarrisSep 12, 2025
  The CLEAN FILTER message on your QCA Spas Hot Tub means that you should remove, clean, and reinstall the filter per the manufacturer’s instructions.
C
christina88Sep 8, 2025
Why does my QCA Spas QCA Paradise display --F° or --C°?
- M
  michele80Sep 8, 2025
  The display of --F° or --C° on your QCA Spas Hot Tub indicates that the temperature will be displayed after the pump has been running for 2 minutes.
A
adam97Sep 5, 2025
What does SENSOR B SERVICE RQD mean on my QCA Spas QCA Paradise?
- P
  Pamela ParkerSep 5, 2025
  The SENSOR B SERVICE RQD message on your QCA Spas Hot Tub indicates that the sensor plugged into the Sensor “B” jack is not working. If the problem persists, contact your dealer or service organization. This message may appear temporarily in an overheat situation and disappear when the heater cools.