Qualcast XSS41A - User Manual

ASSEMBLY
PREPARING TO MOW
Lift the flap and
hook the grass bag
over the plastic
hooks on the rear
of the mower.
Adjust the cutting
height via the lever
located by the rear
right hand wheel.
Fill the petrol tank with 0.8l of normal 95 Octane petrol
(standard unleaded) using a funnel and measuring jug.
When starting a cold
engine, press down the
primer fully 3~5 times.
When starting a warm
engine, the primer
does not need to be
used.
To start the engine slowly
pull the start cord out
until resistance is felt
(approx 10-15cm) then
start the engine with a
sharp vigorous pull.
In cold weather it may be necessary to repeat the cold engine starting
process.
To stop the mower release the stop/start
bar.
IMPORTANT INFORMATION!
Always read the instruction manual thoroughly
before starting the lawnmower.
Never allow the starter cord to snap back.
Check the oil level before every use. Always use high quality detergent oil classified
SAE30 oil (or equivalent eg 5W 30, often termed as 4 Stroke lawn mower oil).
Unpack the lawn mower ensuring all parts are present
(see parts list overleaf) before discarding the packaging.
Align the lower handle
with the holes in the
deck. Fix the lower
handle using the 4 handle
fixing bolts onto the deck
firmly with supplied
wrench.
3
Locate the rope guide
over the right hand
bolt so the 90° bend
sits on top of the
handle bar and secure
using the plastic knob.
Locate upper handle
bar on lower with the
bolts. Secure the left
bolt using plastic
tightening knob
ensuring cables are
not twisted.
Follow these steps to ensure quick and easy set up
every time.
5
The engine does not
come with oil. Add
0.5 litres of oil.
CHECK THE OIL LEVEL
BEFORE EVERY USE.
7
6
Slowly pull out starter
cord & hook it through
the eye of rope guide.
You should ALWAYS
start your mower
from this position.
11
Hold the stop/start bar
firmly to the handle to
disengage the motor
brake and automatic
cut out.
If you have any difficulties please contact the
helpline on 01904 727500
email support@gardenservicecentre.co.uk
or visit www.gardenservicecentre.co.uk
MOWING THE LAWN
1
2
9
10
Using the cable
clamp provided,
secure the cables to
the handle without
trapping them.
4
8
1
2
Engine stop
Engine start
Add
Full

Summary

Assembly

Align Lower Handle

Align the lower handle with the holes in the deck and fix using the 4 handle fixing bolts.

Attach Upper Handle

Locate upper handle bar on lower handle with bolts and secure left bolt with plastic knob, ensuring cables are not twisted.

Install Rope Guide

Locate the rope guide over the right hand bolt so the 90° bend sits on top of the handle bar and secure using the plastic knob.

Secure Cables

Using the cable clamp provided, secure the cables to the handle without trapping them.

Preparing to Mow

Attach Grass Bag

Lift the flap and hook the grass bag over the plastic hooks on the rear of the mower.

Set Cutting Height

Adjust the cutting height via the lever located by the rear right hand wheel.

Add Engine Oil

The engine does not come with oil. Add 0.5 litres of oil; check the oil level before every use.

Prepare Starter Cord

Slowly pull out starter cord and hook it through the eye of rope guide; always start mower from this position.

Mowing the Lawn

Fill Petrol Tank

Fill the petrol tank with 0.81 of normal 95 Octane petrol (standard unleaded) using a funnel.

Start Engine

Press primer 3-5 times for cold start. Hold stop/start bar firmly and pull starter cord with a sharp vigorous pull.

Stop Engine

To stop the mower, release the stop/start bar.

Important Information and Support

Key Operating Notes

Read manual before use. Repeat cold start in cold weather. Never let starter cord snap back. Check oil level before use.

Contact Information

For difficulties, contact helpline 01904 727500, email support@gardenservicecentre.co.uk, or visit www.gardenservicecentre.co.uk.

Qualcast XSS41A Specifications

General

Brand	Qualcast
Model	XSS41A
Category	Lawn Mower
Language	English