To Next PageTo Next Page
Need help?Do you have a question about the Quantum Audio QZA4400.4 and is the answer not in the manual?
Output Power| output_power_1_ohm | 1 x 2000W |
|---|---|
| output_power_2_ohm | 1 x 1000W |
| rated_output_power_1_ohm | 1 x 600W |
Frequency and Signal| frequency_response | 10Hz - 150Hz |
|---|---|
| signal_to_noise_ratio | >90dB |
| total_harmonic_distortion | <.05% |
Input and Crossover| low_input_level | 285mV - 6V |
|---|---|
| crossover_frequency | 40Hz - 150Hz |
| crossover_slope | 12dB |
Additional Features| bass_eq | 18dB @ 45Hz |
|---|---|
| subsonic_filter | 15Hz - 55Hz |
| bass_remote | Yes |
Power| input_voltage | 11.2V - 14.4V |
|---|
Output Power| output_power_1_ohm | 1 x 3000W |
|---|---|
| output_power_2_ohm | 1 x 1500W |
| rated_output_power_1_ohm | 1 x 900W |
Frequency and Signal| frequency_response | 10Hz - 150Hz |
|---|---|
| signal_to_noise_ratio | >90dB |
| total_harmonic_distortion | <.05% |
Input and Crossover| low_input_level | 285mV - 6V |
|---|---|
| crossover_frequency | 40Hz - 150Hz |
| crossover_slope | 12dB |
Additional Features| bass_eq | 18dB @ 45Hz |
|---|---|
| subsonic_filter | 15Hz - 55Hz |
| bass_remote | Yes |
Power| input_voltage | 11.2V - 14.4V |
|---|
Output Power| output_power_1_ohm | 1 x 4000W |
|---|---|
| output_power_2_ohm | 1 x 2000W |
| rated_output_power_1_ohm | 1 x 1200W |
Frequency and Signal| frequency_response | 10Hz - 150Hz |
|---|---|
| signal_to_noise_ratio | >90dB |
| total_harmonic_distortion | <.05% |
Input and Crossover| low_input_level | 285mV - 6V |
|---|---|
| crossover_frequency | 40Hz - 150Hz |
| crossover_slope | 12dB |
Additional Features| bass_eq | 18dB @ 45Hz |
|---|---|
| subsonic_filter | 15Hz - 55Hz |
| bass_remote | Yes |
Power| input_voltage | 11.2V - 14.4V |
|---|
Output Power| output_power_4_ohms | 4 x 100W |
|---|---|
| output_power_2_ohms | 4 x 200W |
| bridged_output_power_4_ohms | 2 x 1000W |
Frequency and Signal| frequency_response | 10Hz - 25KHz |
|---|---|
| signal_to_noise_ratio | >90dB |
| total_harmonic_distortion | <.05% |
Input and Crossover| low_input_level | 285mV - 6V |
|---|---|
| crossover_frequency_low | 30Hz - 150Hz |
| crossover_frequency_high | 10Hz - 1.2KHz |
Additional Features| crossover_slope | 12dB |
|---|---|
| bass_eq | 18dB @ 45Hz |
| input_voltage | 11.2V - 14.4V |
Output Power| output_power_4_ohms | 4 x 200W |
|---|---|
| output_power_2_ohms | 4 x 400W |
| bridged_output_power_4_ohms | 2 x 1200W |
Frequency and Signal| frequency_response | 10Hz - 25KHz |
|---|---|
| signal_to_noise_ratio | >90dB |
| total_harmonic_distortion | <.05% |
Input and Crossover| low_input_level | 285mV - 6V |
|---|---|
| crossover_frequency_low | 30Hz - 150Hz |
| crossover_frequency_high | 10Hz - 1.2KHz |
Additional Features| crossover_slope | 12dB |
|---|---|
| bass_eq | 18dB @ 45Hz |
| input_voltage | 11.2V - 14.4V |
Warranty details for products purchased in the U.S.A. from authorized dealers.
Covers defects in material and workmanship for one year under normal use.
Excludes units subjected to misuse, abuse, neglect, accident, or unauthorized modifications.
Contact retailer or visit website for warranty service details.
Identifies the product category as MOSFET power amplifiers.
Designates this document as the owner's manual for the amplifiers.
Congratulates user on purchase and highlights appreciation for fine musical reproduction.
Advises attaching the sales receipt for warranty service purposes.
Recommends professional installation by an authorized retailer for optimal performance.
Recommends checking the website for the latest product information.
Fuse power wire within 12" of the battery to protect the car's battery.
Use high-grade connectors for maximum power transfer and secure connections.
Route wires under carpet/panels to avoid damage and ensure clean installation.
Exercise caution when mounting to avoid puncturing vehicle lines or the gas tank.
Run signal wires away from electrical wires to prevent induced noise.
Keep ground wires short and ground all units at the same point to reduce noise.
Avoid sharp edges when running wires; use grommets for protection.
High power systems can cause hearing loss; listen at safe levels.
Protects speakers from DC voltage at the output stage by shutting down the amplifier.
Protects the amplifier from shorts in speakers or wiring by shutting it down.
Shuts down the amplifier when it reaches excessively high temperatures to cool off.
Diagnostic LED illuminates when the amplifier is on and receiving power.
Features variable crossover for low-pass and high-pass filtering for specific models.
Heavy gauge blocks for maximum power/signal transfer with minimal resistance.
Variable 0-12 dB bass boost at 45Hz for enhanced low frequency performance.
Full range line outputs for connecting additional amplifiers, buffered to reduce signal loss.
Protects the amplifier against short circuits and excessive current.
Automatically turns amplifier on/off with the head unit, also resets protection circuits.
Allows fine-tuning of level matching between the source and the power amplifier.
Lists impedance stability for different amplifier models (e.g., 1 Ohm Mono, 2 Ohm Stereo).
Guidance on selecting a mounting location for the amplifier, emphasizing ventilation.
Instructions on marking and drilling holes for mounting the amplifier.
Instructions for connecting the amplifier's power to the car battery.
Connect the amplifier's ground terminal to the car chassis.
Connects the amplifier's remote turn-on to a 12V source for operation.
Connects RCA outputs from the head unit to the amplifier's RCA input terminals.
Run signal wires away from electrical wires to avoid induced noise.
Use at least 16 gauge speaker wire for connections.
Ensure proper phasing (positive to positive, negative to negative) for optimal bass response.
Amplifier speaker terminals are internally paralleled for easier multi-woofer connections.
Diagrams showing single and dual subwoofer connections (1 Ohm Minimum).
Caution against loads below 1 Ohm to prevent overheating and damage.
Explains bridging for mono output to drive a subwoofer or center channel.
Both right and left RCA connections must be made for bridged mode.
Caution against loads below 4 Ohms in bridged mode to prevent damage.
Diagram illustrating 4 channel bridged connections (4 Ohm Minimum).
Caution against loads below 2 Ohms in stereo mode to prevent overheating.
Guidance on mounting the remote module and running its control wire away from electrical noise.
Details the built-in variable crossover for selecting low-pass or high-pass filters.
Advises selecting crossover points based on speaker operating range.
Explains the bass boost feature, adjustable from 0 to 12 dB at 45Hz.
Guides on adjusting input gain to match source output without distortion.
How to set gain for maximum output without distortion at ~3/4 volume.
Warning against overdriving speakers to prevent permanent damage.
States most problems are due to improper installation, not equipment failure.
Lists causes and solutions for 'No Output' issues.
Lists causes and solutions for 'Low Output' issues.
Lists causes and solutions for 'Engine Noise' issues.
Lists causes and solutions when the 'Red Protection L.E.D. Illuminated'.
Detailed technical specifications for specific amplifier models.
Detailed technical specifications for other amplifier models.
