QuietCool IT-RFSWITCH-01 User Manual

Rev 1.0
Page 1 of 4
O
verview
This document summarizes introductions for operating hub IT-RFHUB-01 and in-wall switch IT-RFSWITCH-01. Working as a paired set, IT-RFHUB-01
and IT-RFSWITCH-01 can remotely control the QuietCool Whole House Fans of QC Manufacturing Inc at up to three different speeds.
Key Specifications
IT-RFHUB-01 (Hub):
Voltage: 120V
Frequency: 60Hz
Motor load: 1HP, 735W (Max)
IT-RFSWITCH-01 (Switch):
Voltage: 3VDC (2 AAA batteries)
Battery Standby Current: ≤10uA
RF working distance: 100ft (no obstructions)
Warning:
- Disconnect power at the circuit breaker
before installing or servicing
- Use wires rated at least 105*C – copper
only
- Installation/wiring must be in accordance
with national and local code regulations
- Keep the enclosure cover closed at all
times when not servicing.
- Cover all unused wires with a wire
connector
FCC Regulations
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Statement:
"This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help."
FCC Caution:
Changes or modifications not expressly approved by the part responsible for compliance could void the user's authority to operate the equipment.
IT-RFSWITCH-01 Wall Switch & IT-RFHUB-01 Hub
Installation Guide

QuietCool IT-RFSWITCH-01 Specifications

General

Brand	QuietCool
Model	IT-RFSWITCH-01
Category	Switch
Language	English

Summary

Overview and Specifications

Introduction to Hub and Switch

Introduces the IT-RFHUB-01 hub and IT-RFSWITCH-01 switch for remote fan control.

Key Product Specifications

Lists voltage, frequency, motor load for the hub, and voltage, battery, RF distance for the switch.

Safety and Regulatory Information

Installation and Usage Warnings

Critical safety warnings for power disconnection, wiring, and enclosure during installation and servicing.

FCC Compliance and Cautions

Details FCC Part 15 compliance, interference rules, and user cautions regarding modifications.

Installation Guide

In-wall Switch Installation

Step-by-step guide for installing the in-wall switch, including battery insertion.

IT-RFHUB-01 Hub Installation and Configuration

Covers hub mounting, wiring to the fan motor, and dip switch settings for fan speed.

Operation and Status Indicators

Hub Power-On and Fan Speed Cycling

Explains hub power indicators and how the 'Test' button cycles fan speeds.

Pairing Hub with In-Wall Switch

Detailed procedure for establishing a wireless connection between the hub and the in-wall switch.

In-Wall Switch Sleep Mode and Wake-up

Describes the auto-sleep function of the switch and how to wake it for status checks.

In-Wall Switch LED Status Reporting

Explains how switch LEDs display fan status, connection health, and operational modes.

Advanced Operation and Notes

LED Status in Sleep Mode and Normal Operation

Interprets LED behavior in sleep mode and normal operation for different fan states.

Changing Timer and Speed Settings

Guides on how to adjust fan timer and speed settings using the in-wall switch buttons.

Important Operation Notes and Troubleshooting

Key notes on timer dependency and troubleshooting hub indicator blinking issues.