Need help?Do you have a question about the Quietside ODW-120A and is the answer not in the manual?
General| Brand | Quietside |
|---|---|
| Model | ODW-120A |
| Category | Water Heater |
| Language | English |
Explains the meaning of danger, warning, caution, and remark icons.
Outlines immediate actions to take if a gas leak is detected.
Provides warnings related to combustion, temperature, and child safety.
Advises on maintaining safe distances from flammable materials and unit clearances.
Details electrical safety and cautions against improper use.
Contains notes on filter cleaning, area maintenance, and environmental factors.
Illustrates and labels the primary components of the water heater unit.
Describes the display, indicators, and buttons of the remote controller.
Guides through essential checks and turning on the unit for the first time.
Explains how to adjust and check the water temperature for use.
Describes the unit's internal freeze protection and external plumbing protection.
Provides steps for draining the unit to prevent freezing during inactivity.
Lists key areas for periodic inspection of the unit and its components.
Details how to clean the exterior of the unit and the remote controller.
Explains the procedure for checking and cleaning the water drain valve filter.
Addresses issues with unit ignition and lack of hot water production.
Covers problems related to incorrect water temperature and slow heating.
Discusses issues with insufficient hot water and fluctuating temperatures.
Addresses issues with the power button and the heater stopping combustion.
Explains normal occurrences like white smoke and air bubbles in hot water.
Lists error codes and corresponding actions for troubleshooting.
Outlines what information is needed when contacting service.
Details availability of repair parts and considerations for re-installation.
Provides detailed technical specifications for different models.
Shows exploded views of the case and neutralizer assemblies.
Illustrates the various parts that make up the burner assembly.
Shows the components involved in the water line connections.
Lists all parts with their corresponding numbers and names.
Shows exploded views of the case and neutralizer for larger models.
Illustrates the burner assembly parts for the larger ODW models.
Shows the water line assembly for the larger ODW models.
Lists parts for the larger ODW models.
Emphasizes risks of improper installation and misuse.
Stresses following manual instructions and local codes for installation.
Details the items included with the water heater unit.
Lists accessories not included but potentially needed for installation.
Advises on approved venting materials and snow accumulation concerns.
Guides on checking gas supply, power requirements, and water quality.
Provides guidance on using solar pre-heaters and periodic unit checks.
Details requirements for indoor installation, ambient temperature, and avoiding hazards.
Advises on venting location, avoiding heat-sensitive materials, and airflow.
Warns against installing near chemicals, dust, or areas affecting exhaust.
Specifies minimum distances from combustible materials and for service access.
Details clearance requirements for the vent termination.
Provides a table with specific clearance requirements from various building openings.
Guides on securely mounting the unit to the wall, ensuring it is level.
Specifies approved PVC pipe types and limitations for venting.
Warns against improper venting, damaged components, and objectionable noise.
Details requirements for indoor installation and upward slope for outdoor terminals.
Advises on spacing for multiple units and keeping hazardous items away from terminals.
Provides notes on pipe types, lengths, elbows, and a diagram of the venting setup.
Suggests inspection openings for vent pipes in enclosed spaces.
Specifies dimensions (Z) for air intake and flue gas outlet holes.
Details PVC pipe lengths (X, Y) and flue terminal insertion.
Guides on attaching the terminal kit to the wall using screws.
Explains the installation and orientation of the 90-degree PVC elbow for the air intake.
Presents alternative venting configurations and pipe penetration methods.
Provides a table for calculating maximum vent lengths based on elbows.
Offers advice on vent pipe routing, hazardous substances, and condensate management.
Details requirements for CO detector installation on each floor and in the unit room.
Specifies approved vent terminations and the required identification plate.
Lists locations where vent termination is prohibited due to condensate issues.
Instructions for turning off gas and crucial safety warnings before operation.
Specifies minimum and maximum inlet gas pressure for Natural Gas and Propane.
Guides on sizing gas pipes, installing shut-off valves, and performing leak tests.
Provides tables for recommended gas pipe sizes based on distance and capacity.
Offers tables for propane pipe sizes based on supply pressure and capacity.
Confirms suitability for potable water and warns against using submerged parts.
Explains installation requirements for the pressure relief valve.
Advises on approved piping materials, hazard prevention, and mixing valves.
Details minimum water pressure (29 PSI) for attic installations and pump system needs.
Covers approved piping types, shut-off valves, and required pressure ranges.
Specifies acceptable water quality parameters to ensure reliable operation.
Illustrates the recommended piping setup for a basic installation.
Shows the piping configuration for a hot water re-circulation system.
Warns about turning off power before servicing and proper wire labeling.
Details electrical code compliance and power supply specifications (120 VAC, 60Hz).
Specifies GFI outlet, separate circuit, breaker, and grounding connections.
Provides a detailed wiring diagram for the ODW-150A to 199A models.
Explains the critical step of filling the condensate trap and annual cleaning.
Details periodic checks for venting system integrity and burner flame consistency.
Guides on operating the pressure relief valve and warnings for overheating.
Outlines steps for testing the unit before customer handover.
Provides instructions for lighting the unit and shutting it down safely.
Tables showing GPM output versus incoming water temperature for ODW-099A.
Tables showing GPM output versus incoming water temperature for ODW-120A.
Tables showing GPM output versus incoming water temperature for ODW-180A.
Tables showing GPM output versus incoming water temperature for ODW-199A.
Provides detailed dimensional drawings for the ODW-099A and ODW-120A models.
Provides detailed dimensional drawings for the ODW-180A and ODW-199A models.
To Next Page
