RAB Lighting STL360HBW User Manual

Specifications:
Switching Capacity 8 amps
1000 watts Incandescent and 250 watts
Fluorescent
Voltage: 120 volts
Protection Pattern: 180° forward
360° below and to all sides
Time Adjustment: 5 seconds to 12 minutes
Power Consumption: 1 watt
Surge protection: 6000 volts
Cautions:
TURN OFF ALL POWER AT CIRCUIT BREAKER / FUSE PANEL.
■
Read entire Installation Manual before proceeding.
■
All wiring should comply with local electrical codes
and requires a qualified electrician.
■
The total lighting load connected to STL360 must not
exceed (1000 watts incandescent or quartz, 250 watts
fluorescent). To switch more wattage an electrician can
install a relay.
■
Line Carrier Remote Control Systems such as X-10,
Leviton or Radio Shack are incompatible with sensors and
may cause false activations.
■
Do not install sensors on a circuit that feeds motor
loads such as kitchen appliances, HVAC equipment,
washer/dryer, or garage door openers.
■
Sensor functions best when the direction of expected
movement is across its detection pattern, not towards
the sensor.
■
Mount 6’-12' high for optimum range and detection.
The STEALTH360 is the
most reliable and technically
advanced motion-activated light
control ever produced. This techni-
cal manual is written for electrical
professionals who wish to maximize
the performance and reliability of this
superb sensor.
RAB welcomes your questions
or comments.
Please call 888 722-1000,
or email tech@rabweb.com.
Thank you for purchasing a RAB
sensor.
STL360H
STL360HBW
STL360Q1
STL360Q3W
STL360Q2W
Installation Manual

RAB Lighting STL360HBW Specifications

General

Category	Accessories
Type	Motion Sensor
Color	White
Voltage	120-277V
Mounting Type	Wall mount
Sensing Range	360 degrees

Summary

STEALTH 360 Product Overview and Safety

Product Specifications

Key technical details including switching capacity, voltage, protection pattern, time adjustment, and surge protection.

Installation and Operation Cautions

Essential warnings for safe installation and operation, including power, wiring, load limits, and placement.

Understanding Stealth 360 Operation

LED Detection Indicators

Explains the function of scanning LEDs as indicators for security device operation and mode.

Light Duration and Manual Control

Details light duration adjustment and manual control options via the light switch.

Sensor Adjustment Features

Guides on using adjustment tools and knobs to fine-tune sensor settings like sensitivity.

Optimal Location Selection

Area Coverage and Mounting Height

Describes the detection pattern, coverage area, and how mounting height affects range.

Addressing Difficult Locations

Identifies challenging locations and methods to improve performance, like reducing sensitivity or masking.

Stability and Light Placement

Advises on ensuring stable mounting and correct sensor placement relative to lights.

Installation and Wiring Guide

Floodlight Kit Assembly

Details the steps for assembling floodlight kits onto the CU4 EZ plate.

Wiring Instructions

Provides a diagram and steps for connecting power, ground, and fixture wires.

Multiple Fixture and Sensor Wiring

Discusses wiring multiple fixtures/sensors and power quality considerations.

Adjusting Sensor Settings

Time and Photocell Adjustment

Explains how to adjust light-on time and photocell for night-only or 24-hour operation.

Sensitivity and Evening Timer

Details how to adjust sensitivity and set the Evening Timer for continuous lighting after dusk.

Sensor Modes Explained

Automatic and Evening Timer Modes

Describes Automatic Mode and how to set and use the Evening Timer Mode.

Test and Manual Override Modes

Explains how to enter Test Mode and use Manual Override Mode for continuous light.

Walk Testing Procedure

Performing a Walk Test

Guides on entering Test Mode and walking through the detection pattern to check coverage.

Adjusting for Coverage

Advises on adjusting sensor aiming, sensitivity, and using lens masks for optimal coverage.

Troubleshooting and Technical Tips

Lights Turn On/Off Inappropriately

Addresses common issues like false triggers, reflections, and incorrect wiring.

Lights Do Not Turn On

Provides solutions for issues where lights fail to activate, including wiring and photocell checks.

Lights Turn Off Too Quickly

Offers tips for when lights extinguish prematurely, often due to reflected light.

Range Appears Limited

Explains causes for limited detection range and solutions like adjusting mounting height or aiming.

Replacement Parts and Support

Replacement Lamps

Lists compatible replacement lamps for various STL360 models.

Accessory Kit Contents

Details the components included in the accessory kit for installation and adjustments.

Support and Contact Information

Provides contact details for technical support, sales, and website resources.